R (d) Installation of the torque shaft 6210CM (6260CM)
R 1_ Put the universal joint (3) in the installation position. Make
R sure that the flange aligns with the torque shaft (4).
R 2_ Install the bolts (6) and the nuts (5). Tighten the nuts (5)
R with your hand.
R 3_ TORQUE the nuts (5) to between 1.02 and 1.24 m.daN (90.26 and
R 109.73 lbf.in).
R (e) Install the PIN RIGGING FLAPS (2).
R 1_ Make sure that you can remove/install the rigging pin (2)
R easily.
R 2_ If you cannot remove/install the rigging pin (2) easily, do
R the adjustment procedure again.
R (f) Make sure that:
R - You cannot see the spline engagement groove at the movable
R joint
R - The dimension "A" is a minimum of 6.5 mm (0.2559 in.) at the
R movable joint.
R (g) Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
R (Ref. TASK 27-50-00-000-003)
R Subtask 27-54-00-820-053
R C. Adjustment of the Flap Track No. 3
R (1) Install the PIN RIGGING FLAPS (2) at the track 3.
R (2) If you cannot install the PIN RIGGING FLAPS (2) easily, do the steps
R that follow:
R (a) Removal of the Torque Shaft 6218CM (6268CM)
R 1_ Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
R PIVOT (98D27504030001) on a flap torque shaft, outboard of the
R component that you will remove (Ref. TASK 27-50-00-400-003).
R 2_ Remove the nuts (12) and the bolts (11) from the torque shaft
R (10).
R 3_ Remove the universal joint (13).
R (b) Adjustment of the flap drive system (for free rigging pin).
R 1_ Loosen the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
R PIVOT as necessary to turn the torque shafts.
R 2_ Turn the torque shaft 6224CM (6274CM) four turns in the
R extension direction.
R 3_ Turn the torque shaft 6224CM (6274CM) in the retraction
R direction until the rigging pin (2) can be installed easily.
R 4_ If the torque shaft 6224CM (6274CM) is accidentally turned too
R far in the retraction direction:
R - Do the adjustment procedure again, until the rigging pin (2)
R can be installed easily.
R (c) Preparation for Installation
R CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT._______
R GREASE AND ASSEMBLY PASTE DO NOT MIX.
R WARNING : USE A PROTECTIVE EYE SHIELD/GOGGLES WHEN YOU USE_______
R COMPRESSED AIR. DEBRIS AND/OR HIGH PRESSURE AIR CAN
R DAMAGE YOUR EYES.
R WARNING : DO NOT PUT COMPRESSED GAS IN CONTACT WITH YOUR SKIN._______
R THE GAS CAN GO THROUGH THE SKIN AND MAKE BUBBLES IN THE
R BLOOD. THIS CONDITION CAN KILL YOU.
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER_______
R SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵4(154)
