-
FLP RH PROX SNSR 1 OR WIRING TO
LGCIU 1
-
FLP RH PROX SNSR 2 OR WIRING TO
LGCIU 2.
-
the MCDU shows the SFCC 1 page.
-
the MCDU shows the SYSTEM REPORT/TEST PAGE.
-
the MCDU shows the SFCC 2 page.
-
the MCDU shows the SFCC 2 SYSTEMSTATUS FLAP page. These subsequent messages must not occur:
-
FLP 2 NO SFCC 1 DATA CHECK WIRING & SFCC 1
-
FLP 2 FAULTY FLP 1 DATA CHECK SFCC 1 OR 2
-NO LGCIU 2 DATA CHECK WIRING TO FLP 2
-
FLP LH PROX SNSR 2 MISADJUSTMENT and FLP LH PROX SNSR 1 OR WIRING TO LGCIU 1
-
FLP LH PROX SNSR 1 OR WIRING TO
LGCIU 1
-
FLP LH PROX SNSR 2 OR WIRING TO
LGCIU 2
-
FLP RH PROX SNSR 2 MISADJUSTMENT and FLP RH PROX SNSR 1 OR WIRING TO LGCIU 1
-
FLP RH PROX SNSR 1 OR WIRING TO
LGCIU 1
-
FLP RH PROX SNSR 2 OR WIRING TO
LGCIU 2.
1EFF : ALL 1 27-51-44Page 507 1 1 May 01/04R 1 1 1CES 1
Subtask 27-51-44-710-057
D. Complete Test
(1)
Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slatcontrol lever on panel 114VU.
(2)
Do an operational test of the flap system (Ref. TASK 27-54-00-710-001).
5. Close-up
________ Subtask 27-51-44-410-057
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the lower kink seal, the cushion seals and the upper kink seals on the flaps (Ref. TASK 27-54-61-400-006).
(3) Retract the flaps fully (Ref. TASK 27-50-00-866-009). Subtask 27-51-44-942-057
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
STRUT - INTERCONNECTING - INSPECTION/CHECK
__________________________________________
TASK 27-51-44-200-001
Detailed Visual Inspection of the Flap Interconnecting Strut and Attachments
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 275144-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers R No specific warning notice No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) 98D27504008000 1 GO/NO GO GAGE 98D27504031000 1 PIN-SETTING 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 15-007 AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
Material No. 19-010 USA AMS 5687
LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵4(116)
