2.
On the MCDU: On the MCDU:
-push the line key < SFCC 1 (2). - the MCDU shows the SFCC 1 (2) menu. NOTE : Use the SFCC 2 to do this test again for the WTB 33CV-B and 34CV-B.
____
3.
Push the NEXT PAGE button. - the MCDU shows the next page of the SFCC 1 (2) menu.
4.
Push the line key TEST/RESET FLP - the MCDU shows the SFCC 1 (2) FLAP >. TEST/RESET menu.
5.
Push the line key < WTB/POB TEST. - the MCDU shows the SFCC 1 (2) FLAP WTB/POB TEST instructions.
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
6.
Push the line key < CONTINUE
7.
Push the line key < START TEST.
NOTE : If the line key < START
____ TEST is not shown, do the instructions the MCDU shows.
8.
Push the line key < RETURN frequently until the SYSTEM REPORT/TEST - F/CTL menu is shown.
9.
Make sure that the WTBs are not set.
10.
Open the circuit breakers 5CV and 6CV (flap and slat system 1).
11.
Close the circuit breakers 7CV and 8CV (flap and slat system 2).
-
the MCDU shows the next page of the SFCC 1 (2) FLAP WTB/POB TEST instructions.
-
the MCDU shows that the FLAP WTB/POB TEST is IN PROGRESS.
-
the MCDU shows in less than 2 minutes SFCC 1 (2) PERFORMED NO FAULTS RESULT NOT STORED
NOTE : When the test of the Wing Tip
____ Brake and the Pressure Off Brake will not operate,the subsequent message(s) is (are) displayed: Corrupted RAM - Return On Line , or Pin Prog Fault. Then push the <RETURN key frequently to show the CFDS menu page. Then do the test again after the menu mode is displayed.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page 527 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------12. Use the SFCC 2 to do this test again.
13. Push the line key <RETURN frequently until the CFDS menu page is shown.
14. Close the circuit breakers 5CV and 6CV.
15. Set the Slat and Flap control lever to the position 0.
R **ON A/C 301-399,
R Subtask 27-51-00-710-068-A
R A. Operational Test of the Wing Tip Brake and the Pressure-Off Brake
R R R WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
R R R NOTE : Use the Multipurpose Control Display Unit (MCDU) 3 on panel 1VU____ for the test. If the MCDU 3 is defective, use the MCDU 2 on panel 11VU.
R NOTE : When you do this test the flap surfaces will move automatically.____
R R R NOTE : Make sure that the CFDS is not in the SFCC menu mode before you____ start the test. The test will not operate, if a BITE test was completed before. Subsequently Pin Prog Fault will be displayed.
R -------------------------------------------------------------------------------R ACTION RESULT R -------------------------------------------------------------------------------
R 1. Set the Slat and Flap control The Slats and Flaps move to the R lever to the position 3. position 3.
R 2. On the MCDU: - the MCDU shows the SFCC 1 (2) menu. R - push the line key < SFCC 1 (2).
R NOTE : Use the SFCC 2 to do this test again for the WTB 33CV-B and 34CV-B.
____
R 3. Push the NEXT PAGE button. R
R 4. Push the line key TEST/RESET FLP R >.
R 5. Push the line key < WTB/POB TEST. R
R 6. Push the line key < CONTINUE R R
R 7. Push the line key < START TEST. R R NOTE : If the line key < START
____ R TEST is not shown, do the R instructions that the MCDU R shows.
R R R R R R
R R R R R R R R
-
the MCDU shows the next page of the SFCC 1 (2) menu.
-
the MCDU shows the SFCC 1 (2) FLAP TEST/RESET menu.
-
the MCDU shows the SFCC 1 (2) FLAP WTB/POB TEST instructions.
-
the MCDU shows the next page of the SFCC 1 (2) FLAP WTB/POB TEST instructions.
-
the MCDU shows that the FLAP WTB/POB TEST is IN PROGRESS.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵4(46)
