757 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(61)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

STOP
SERVO LEVER
PLATE
INDEX MARKS
STABILIZER TRIM  SERVO LEVER
CONTROL MODULES (STCMs) SEE A
B
PRESSURE LINE TO THE ELEVATOR FEEL CONPUTER
RIG PIN HOLE SERVO LEVER
E/ST2 RETURN LINE
SEE B
PRESSURE LINE BOLT WASHER (4 LOCATIONS)
ELECTRICAL CONNECTOR ELECTRICAL CONNECTOR
SERVO LEVER 
ELECTRICAL 
CONNECTOR 
BOLT, 
WASHERS (QTY 2), 
NUT 
VALVE SOLENOID  BOLT  RETURN LINE  (4 LOCATIONS) 
(8 LOCATIONS)  E/ST1 RIG PIN HOLE  ELECTRICAL CONNECTOR  PRESSURE LINE FOR BRAKE RELEASE 
PRESSURE LINE FOR 
PRESSURE LINE FOR  AIRPLANE NOSE DOWN 
AIRPLANE NOSE UP  MOVEMENT 
MOVEMENT 

NOTE: THE RIGHT HYDRAULIC SYSTEM SUPPLIES PRESSURE TO THE RIGHT STCM, THE CENTER HYDRAULIC SYSTEM SUPPLIES PRESSURE TO THE LEFT STCM.
STABILIZER TRIM CONTROL MODULES (STCMs)
A
Stabilizer Trim Control Module Installation
Figure 201 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH STAB TRIM LEVERS ON THE ú

 27-41-05
 CONTROL STAND  ú ú 02 Page 202 ú Jun 20/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

STABILIZER TRIM
CONTROL MODULES
(STCMs)

SEE C PRESSURE LINE TO THE ELEVATOR FEEL COMPUTER RETURN LINE PRESSURE LINE
BOLT WASHER (4 LOCATIONS)
ELECTRICAL ELECTRICALCONNECTOR CONNECTOR
ELECTRICAL CONNECTOR
PRESSURE LINE FOR BRAKE RELEASE BOLT RETURN LINE
SOLENOID
PRESSURE LINE FOR
PRESSURE LINE FORVALVE
AIRPLANE NOSE UP
AIRPLANE NOSE DOWN(8 LOCATIONS)
MOVEMENT
MOVEMENT ELECTRICAL CONNECTOR
STABILIZER TRIM CONTROL MODULES (STCMs)
C

NOTE: THE RIGHT HYDRAULIC SYSTEM SUPPLIES PRESSURE TO THE RIGHT STCM, THE CENTER HYDRAULIC SYSTEM SUPPLIES PRESSURE TO THE LEFT STCM.
Stabilizer Trim Control Module Installation
Figure 201 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH ALTERNATE STAB TRIM ú

 27-41-05
 SWITCHES ON THE CONTROL STAND  ú ú 02 Page 203 ú Jun 20/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

STABILIZER BALLSCREW ACTUATOR
STABILIZER BALLSCREW ACTUATOR
A

1  THE GAGE ASSEMBLY CAN BE USED TO ACCURATELY SET THE STABILIZER DIMENSION B TO 19.07 |0.01 INCHES.
TO USE, PUT THE GAGE ASSEMBLY AGAINST THE
BALLSCREW SUCH THAT THE LOWER BOLTHEAD IS
ON THE SHOULDER OF THE LOWER STOP. MAKE
SURE THAT THE FEELER BLADE CANNOT BE PUT
BETWEEN THE GAGE ASSEMBLY UPPER BOLTHEAD
AND THE SHOULDER OF THE UPPER STOP. MAKE
SURE THE SHOULDER OF THE UPPER STOP DOES
NOT TOUCH THE UPPER BOLTHEAD.

Measurement of Stabilizer Dimension B
Figure 202

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-05
 ALL  ú ú 01 Page 204 ú Jun 20/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 (2)  
Access Panel
 311AL Forward Stabilizer Compartment

 E.
Prepare for the Removal

 S 862-002
 (1)  
Supply power to the right and center hydraulic systems
 (Ref 29-11-00).

 S 862-003

 (2)  
Move the stabilizer until Dimension B on the stabilizer ballscrew actuator is 19.07 | 0.01 inches (484.4 +/- 0.25 mm) (Fig. 202).

 S 862-004

 (3)  
Remove the power from the right and center hydraulic systems (Ref 29-11-00).

 S 862-005

 (4)  
Put the RIGHT and CENTER STAB TRIM CUTOUT switches on the control stand panel, P10, to the CUTOUT position.

 S 862-006

 (5)  
Open these circuit breakers on the overhead panel, P11, and attach DO-NOT-CLOSE tags:
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(61)