757 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(177)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

SUPPORT AND THE FLANGED SHIM. FLANGED SHIM IS
THE SHIM WITH TWO COATS OF PRIMER AND
FAYING SURFACE SEAL
INSTALLED ON THE CARRIAGE AND IS NOT REMOVABLE.
SEE TABLE 1.
APPLY SEALANT TO THE BOLT AFTER SHIM CHANGE
Vertical Adjustment for the Inboard TE Flap
Figure 504 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-02
 ALL  ú ú 02 Page 509 ú Jun 20/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

CONFIGURATION  AVERAGE  MAXIMUM  MINIMUM 
ON JACKS + ENGINES  -0.27`  0.44`  -1.72` 
ON GEAR + ENGINES  0.19`  2.66`  -2.92` 
ON GEAR + ENGINES +  -0.12`  0.40`  -0.53` 
3000 LBS FUEL 

INBOARD FLAP WING REFERENCE PLANE
TABLE 1
WRP

CARRIAGE  (TRACE)
NOTE:  WRP AND TRACE OF MFRP ARE NOMINALLY PARALLEL.
WING REFERENCE PLANE (WRP) TO INBOARD FLAP MAIN FLAP REFERENCE PLANE (MFRP)

0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
MFRP TO WRP ANGLE (DEGREE) INBOARD FLAP ANGLE TO TE HEIGHT CONVERSION
Vertical Adjustment for the Inboard TE Flap Figure 504 (Sheet 3)
D02086
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-02
 ALL  ú ú 01 Page 510 ú Jan 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-02
 ALL  ú ú 01 Page 511 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
SERRATED PLATE ASSEMBLY

Fit and Fair Requirement for the Inboard TE Flap
Figure 505 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-02
 ALL  ú ú 03 Page 512 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

CONFIGURATION  INCHES (mm) AVERAGE  INCHES (mm) MAXIMUM  INCHES (mm) MINIMUM 
ON JACKS + ENGINES  -0.26 (-6.604)  -0.16 (-4.064)  -0.40 (-10.160) 
ON GEAR + ENGINES  -0.16 (-4.064)  0.08 (2.032)  -0.30 (-7.620) 
ON GEAR + ENGINES +  -0.25 (-6.350)  -0.08 (-2.032)  -0.44 (-11.176) 
3000 LBS FUEL 

____NEGATIVE DIMENSION INDICATES THE FLAP IS ABOVE THE PANEL.
NOTE:
MAXIMUM MISFAIR BETWEEN THE LOWER FIXED PANEL AND LOWER SURFACE OF INBOARD FLAP OVER LAST 30 INCHES (762 mm) OF THE OUTBOARD END. MEASUREMENT TAKEN AT THE OUTBOARD END OF THE INBOARD FLAP TABLE 1
CONFIGURATION  INCHES (mm) AVERAGE  INCHES (mm) MAXIMUM  INCHES (mm) MINIMUM 
ON JACKS + ENGINES  -0.10 (-2.540)  0.08 (2.032)  -0.25 (-6.350) 
ON GEAR + ENGINES  -0.01 (-0.254)  0.10 (2.540)  -0.10 (-2.540) 
ON GEAR + ENGINES +  0.04 (1.016)  0.18 (4.572)  -0.16 (-4.064) 
3000 LBS FUEL 

____NEGATIVE DIMENSION INDICATES THE FLAP IS ABOVE THE PANEL.
NOTE:
MISFAIR BETWEEN THE LOWER FIXED PANEL AND LOWER SURFACE OF INBOARD FLAP
MEASUREMENT DOES NOT APPLY OVER THE OUTBOARD 30 INCHES (762 mm) OF THE INBOARD FLAP
TABLE 2

TABLE 3 NOT USED

____A NEGATIVE DIMENSION INDICATES THE INBOARD FLAP IS AFT OF THE OUTBOARD FLAP.
NOTE:
FORWARD/AFT MISFAIR BETWEEN INBOARD/OUTBOARD MAIN FLAPS AT TRAILING EDGE TABLE 4
Fit and Fair Requirement for the Inboard TE Flap

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(177)