S 215-010
(1)
Make sure that the trailing edge (TE) flaps and the leading edge (LE) slats are in the fully retracted position.
S 865-048
(2)
Make sure the flap control lever is in the zero (FLAPS UP) detent, and install a DO-NOT-OPERATE tag on the flap control lever.
S 215-011
(3)
Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
S 495-012
WARNING: USE THE PROCEDURE IN (AMM 32-00-15/201) TO INSTALL THE DOOR
_______ LOCKS. THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(4)
Open the doors for the landing gear and install the door locks (AMM 32-00-15/201).
(5)
Remove the power from the left hydraulic system (AMM 29-11-00/201).
S 495-008
(6)
Install the PDU lock in the TE flap power drive unit (PDU)
(Fig. 506).
S 865-013
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-02
ALL ú ú 01 Page 506 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
S 865-014
(7)
Open these circuit breakers on the overhead panel, P11, and attach DO-NOT-CLOSE tags:
(a)
11B18, WARN ELEX B
(b)
11D31, HYDRAULICS PTU CONT
(c)
11H23, FLAP/SLAT ALTN DR SHUTOFF ARM
(d)
11J18, FLAP LOAD RELIEF
(e)
11J33, WARN ELEX A
S 865-015
(8)
Open these circuit breakers on the power distribution panel, P6, and install DO-NOT-CLOSE tags:
(a)
6D20, ALTN SLAT PWR
(b)
6D23, ALTN FLAP PWR
S 015-016
(9)
Remove the access panels for the TE flaps and open access doors as necessary (Ref 06-44-00).
F.
Inboard TE Flap Adjustment
S 215-017
(1)
Make sure that the TE flaps agree with the conditions that follow before you adjust the inboard TE flaps:
(a)
The outboard flaps are correctly adjusted with the outboard rigging bars (Ref 27-51-14).
NOTE: If you cannot get the outboard flaps to agree with the
____ rigging adjustment (Ref 27-51-14), make sure that the lateral trim correction for the outboard flaps is below the limit (Ref 27-01-00). You must make allowance for rigging by lateral trim correction to get level flight for the airplane.
(b)
The left and right hand side of the outboard flaps are correctly sychronized to each other (Ref 27-51-14).
(c)
The inboard flap that you will not adjust must agree with the angular dimension (Fig. 504) and the vertical mismatch between the inboard and outboard flaps (Fig. 505).
(2)
Remove the aft fairing for the inboard flap track (Ref 27-51-30).
S 025-019
(3)
Remove the trunnion fairing door for the main landing gear (MLG) (Ref 32-12-10).
(4)
Remove the MLG trunnion fairing (Ref 57-51-10).
S 025-018
S 025-002
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-02
ALL ú ú 01 Page 507 ú Jun 20/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
Vertical Adjustment for the Inboard TE Flap
Figure 504 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-02
ALL ú ú 01 Page 508 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 757 MAINTENANCE MANUAL
SHIM AFT ROLLER WING
SUPPORT
SHIM, INBOARD
INSTALL SHIMS ONLY BETWEEN AFT THE ROLLER
MAXIMUM SHIM THICKNESS-0.40 INCH. INSTALL
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 飞行操纵 FLIGHT CONTROLS 4(176)
