(b) If the voltmeter readout is not correct:
- replace the RELAY-L/G POSITION, SYS1 (11GB).
1_ If the fault continues:
- do a check of the wiring of the relay (11GB):
. from pin A/A2 to the circuit breaker (16FN)
. from pin A/A3 to the standby altimeter (3FN)
(Ref. ASM 34-21/01).
a If there is no continuity:
_ - repair the above wiring.
b If there is continuity:
_ - replace the C/B-NAV/STBY/ALTM (16FN).
(2) If the voltmeter readout is not equal to O V:
- replace the RELAY-L/G POSITION, SYS1 (11GB).
(a) If the fault continues:
- replace the LGCIU-1 (5GA1) (Ref. AMM TASK 32-31-71-000-001) and (Ref. AMM TASK 32-31-71-400-001).
1 If the fault continues:
_
- do a check and repair the wiring from the LGCIU1 (5GA1) to the SYS1 L/G position relay (11GB): from pin AB/1B to pin A/X2 (Ref. ASM 32-62/01).
TASK 34-21-00-810-802
Standby Airspeed Information not Accurate
1. Possible Causes
_______________
- IND-STANDBY AIRSPEED (9FN)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R AMM 34-10-00-170-003 Draining and Flushing of Standby Pneumatic Circuits AMM 34-21-00-720-001 Functional Test of the Standby Airspeed Indicator AMM 34-21-26-000-001 Removal of the Standby Airspeed Indicator (9FN) AMM 34-21-26-400-001 Installation of the Standby Airspeed Indicator (9FN)
3. Fault Confirmation
__________________
A. Test
(1) Do the functional test of the standby airspeed indicator (Ref. AMM TASK 34-21-00-720-001).
4. Fault Isolation
_______________
A. If the standby airspeed indicator shows out of tolerance values:
- replace the IND-STANDBY AIRSPEED (9FN) (Ref. AMM TASK 34-21-26-000-001) and (Ref. AMM TASK 34-21-26-400-001).
(1) If the fault continues:
- drain and flush the standby static and the standby total pressure lines (Ref. AMM TASK 34-10-00-170-003).
B. Do the test given in Para. 3.
TASK 34-21-00-810-803
Standby Altitude Information no Accurate
1. Possible Causes
_______________
- ALTM-STANDBY (3FN)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R AMM 34-10-00-170-003 Draining and Flushing of Standby Pneumatic Circuits AMM 34-21-00-720-002 Functional Test of the Standby Altimeter AMM 34-21-22-000-001 Removal of the Standby Altimeter (3FN) AMM 34-21-22-400-001 Installation of the Standby Altimeter (3FN)
3. Fault Confirmation
__________________
A. Test
(1) Do the functional test of the standby altimeter (Ref. AMM TASK 34-21-00-720-002).
4. Fault Isolation
_______________
A. If the standby altimeter shows out of tolerance values:
- replace the ALTM-STANDBY (3FN) (Ref. AMM TASK 34-21-22-000-001) and (Ref. AMM TASK 34-21-22-400-001).
(1) If the fault continues:
- drain and flush the standby static pressure line (Ref. AMM TASK 34-10-00-170-003).
B. Do the test given in Para. 3.
R **ON A/C 001-049, 051-099, 101-105,
TASK 34-21-00-810-804
Metric Altitude Information not Accurate
1. Possible Causes
_______________
- ALTIMETER-METRIC (15FN)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-10-00-170-003 Draining and Flushing of Standby Pneumatic Circuits
AMM 34-21-25-000-001 Removal of the Metric Altimeter (15FN)
AMM 34-21-25-400-001 Installation of the Metric Altimeter (15FN)
3. Fault Confirmation
__________________
A. Test
(1) Not applicable, the fault is evident.
4. Fault Isolation
_______________
A. If the metric altimeter shows out of tolerance values:
- replace the ALTIMETER-METRIC (15FN) (Ref. AMM TASK 34-21-25-000-001) and (Ref. AMM TASK 34-21-25-400-001).
(1) If the fault continues:
- drain and flush the standby static pressure line (Ref. AMM TASK 34-10-00-170-003).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 导航 NAVIGATION 2(92)
