3. Fault Confirmation
__________________
A. Test
(1) Do the Interface test of the IR (system 3) (Ref. AMM TASK 34-14-00-740-001).
4. Fault Isolation
_______________
A. If the test gives the maintenance message FMGC1 (1CA1)/ADIRU3 (1FP3):
- replace the ADIRU-3 (1FP3) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the FMGC1 INPUT bus from the ADIRU3 (1FP3) to the first terminal block (Ref. ASM 34-14/02).
B. Do the test given in Para. 3.
Loss of the FMGC2 Data Input Bus on the ADIRU3
1. Possible Causes
_______________
- ADIRU-3 (1FP3)
- wiring of the FMGC2 INPUT bus from the ADIRU3 (1FP3) to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-12-34-400-001 Installation of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-14-00-740-001 Interface Test of the IR
ASM 34-14/02
3. Fault Confirmation
__________________
A. Test
(1) Do the Interface test of the IR (system 3) (Ref. AMM TASK 34-14-00-740-001).
4. Fault Isolation
_______________
A. If the test gives the maintenance message FMGC2 (1CA2)/ADIRU3 (1FP3):
- replace the ADIRU-3 (1FP3) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the FMGC2 INPUT bus from the ADIRU3 (1FP3) to the first terminal block (Ref. ASM 34-14/02).
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-14-00∞∞∞∞∞∞∞∞∞∞Page A298
May 01/05R
CES
R **ON A/C 001-049, 101-105, 151-199, 201-203,
TASK 34-14-00-810-957
Failure of the IR 1 SDI Pin-Programming
1. Possible Causes
_______________
- ADIRU-1 (1FP1)
- wiring of the defective programming pins
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-12-34-400-001 Installation of the ADIRU (1FP1, 1FP2, 1FP3)
AMM 34-14-00-740-001 Interface Test of the IR
ASM 34-12/01
3. Fault Confirmation
__________________
A. Test Do the Interface test of the IR (system 1) (Ref. AMM TASK 34-14-00-740-001).
4. Fault Isolation
_______________
A. If the test gives the maintenance message WRG : SDI PIN PROG:
- do a check of the SDI pin-programming pins AB/1A, 5A, 6A on the rack connector,
- compare the status of the SDI pin-programming with the status given in the ASM (Ref. ASM 34-12/01).
(1) If the pin programming is incorrect:
- repair the wiring of the defective programming pins (Ref. ASM 34-12/01).
(2) If the pin programming is correct:
- replace the ADIRU-1 (1FP1) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-203, ∞∞34-14-00∞∞∞∞∞∞∞∞∞∞Page A299
May 01/05 CES Failure of the IR 2 SDI Pin-Programming
1. Possible Causes
_______________
- ADIRU-2 (1FP2)
- wiring of the defective programming pins
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 导航 NAVIGATION 2(82)
