R NOTE : The necessary viscosity is 17-23 seconds, 4 mm (0.16 in.)____
R DIN cup.
R (b) Permit the mixture 15 minutes reaction time before use.
R NOTE : Pot life is 8 hours maximum.____
R It will be necessary to add STRUCTURE PAINTS (Material No.
R 16-047) (thinner 62) after approx. 4 hours to keep the
R necessary viscosity.
R NOTE : Conditions for use:____
R - Temperature between 15 DEG.C (59.00 DEG.F) and 30 DEG.C
R (86.00 DEG.F),
R - Relative humidity 35-75% .
R (c) For a textured finish apply the mixture in 1-4 cross coats with a
R GUN - AIR SPRAY, STANDARD PAINT and a NOZZLE DIA 1.5 MM (1/16
R IN).
R NOTE : The necessary coat thickness of a textured finish is____
R between 0.03 mm (0.0011 in.) and 0.09 mm (0.0035 in.).
R NOTE : The textured finish is:____
R - Dust dry after 20 minutes,
R - Transport dry after 8 hours,
R - Fully dry after 7 days at room temperature.
R Over-painting: Between 20 minutes and 12 hours.
R NOTE : If the drying time between the coats is more than 12____
R hours:
R - clean the repair with STRUCTURE PAINTS (Material No. 16-
R 047) (thinner 62) and a lint-free cotton cloth
R MISCELLANEOUS (Material No. 19-003).
R - Rub it with emery cloth, 320-400 grade
R and
R - Clean it with CLEANING AGENTS (Material No. 11-010) and
R a lint-free cotton cloth MISCELLANEOUS (Material No. 19-
R 003).
R NOTE : To make the cure faster you can add heat 60 DEG.C (140.00____
R DEG.F) to the repair area.
R The textured finish is then:
R - Transport dry after 40 minutes,
R - Fully dry after 12 hours.
R Over-painting: Heat-cured for 20 minutes maximum if you
R do not clean or rub the repair.
EFF : ALL
25-00-00Page 879
R (7) Remove the masking tape and the masking paper from the adjacent
R components or areas.
R Subtask 25-00-00-370-054
R C. Repair of the Paint Coating of Thermoplastic Components and Aluminum
R Parts in the Cabin
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE_______
R MATERIAL/S.
R USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
R WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK_______
R AREA WHEN YOU USE SPECIAL MATERIALS.
R IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH
R OR IN YOUR EYES :
R -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15
R MINUTES.
R -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS.
R DO NOT BREATHE THE FUMES FROM THE MATERIAL.
R DO NOT SMOKE WHEN YOU USE THE MATERIAL.
R DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF
R HEAT.
R THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE
R AND SKIN IRRITANTS.
R NOTE : The procedure that follows agrees with the (Ref. FAR 25.853(a-1))____
R (Fire resistant repairs to the passenger compartment).
R NOTE : The procedure is approved for repair of surfaces smaller than 24____
R in.2 (154.83 cm2).
R NOTE : The procedure is approved for repair of surfaces larger than 24____
R in.2 (154.83 cm2) , but only for parts of the component.
R (1) Clean the component with CLEANING AGENTS (Material No. 11-010) and a
R lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).
R (2) Apply masking paper and BONDING AND ADHESIVE COMPOUNDS (Material No.
R 08-074) o the adjacent components and areas.
R (3) Make the repair area smooth with emery cloth, 320-400 grade.
R (4) Clean the repair area with CLEANING AGENTS (Material No. 11-010) and
R a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).
EFF : ALL
25-00-00Page 880
Aug 01/05
R (5) Prepare a mixture for a textured finish.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备1(64)
