(b)
Install the cover (1) and push it to get correct attachment of the velcro tapes.
4. Close-up
________ Subtask 25-11-42-942-050
A. Make sure that the work area is clean and clear of tool(s) and other items.
EFF : ALL
25-11-42Page 406
SEAT - FOURTH OCCUPANT (13MM) - INSPECTION/CHECK
________________________________________________
TASK 25-11-42-200-001
1. Reason for the Job
Inspection/Check of the Fourth Occupant Seat __________________ Detailed Inspection of seat structure and attachment
2. Job Set-up Information______________________ Not Applicable _________
3. Procedure
Subtask 25-11-42-210-050
A. Inspection Check of the Fourth Occupant Seat
(1)
Make sure that the upholstery of the seat is not worn or damaged.
(2)
Make sure that the velcro pads on the cushions of the back of the seat and the headrest are in the correct condition.
(3)
Make sure that all the bolts that attach the seat have no corrosion and are correctly installed.
(4)
Make sure that the seat is not loose and that the fittings are in the correct condition.
(5)
Make sure that the control cable of the seat belt is not worn.
(6)
Make sure that the seat belt and the buckle are in the correct condition.
EFF : ALL
25-11-42Page 601
SEAT - CAPTAIN/FIRST OFFICER (3MS,4MS) - REMOVAL/INSTALLATION
_____________________________________________________________
TASK 25-11-51-000-001
Removal of the Captain/First Officer Seat (3MS, 4MS)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking cap
No specific circuit breaker(s) safety clip(s)
No specific access platform 1.60 m (5 ft. 3 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
25-11-51-991-001-A Fig. 401
25-11-51-991-002-A Fig. 402
EFF : ALL
25-11-51Page 401
3. Job Set-up
__________ Subtask 25-11-51-865-053
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 3MS
122VU COCKPIT SEATS/SEAT CTL/CAPT 1MS1 U11
122VU LIGHTING/FLOOD/CAPT/SIDE 5LE Z05 FOR 4MS
122VU COCKPIT SEATS/SEAT CTL/F/O 1MS2 U14
122VU LIGHTING/FLOOD/F/O/SIDE 4LE Z06
Subtask 25-11-51-010-050
B. Get access to the Avionics Compartment
(1)
Put an access platform near the access door 811 of the avionics compartment.
(2)
Open the access door 811.
4. Procedure
_________
(Ref. Fig. 401/TASK 25-11-51-991-001-A, 402/TASK 25-11-51-991-002-A) Subtask 25-11-51-020-051
A. Removal of the Seat
(1)
In the avionics compartment, disconnect the electrical connector (5).
(2)
Put a blanking cap on the electrical connectors (5) and (6). NOTE : It is necessary to remove the armrest on the side stick side
____ to enable passage of the seat in the cockpit.
(3)
Remove the bolts (7). Remove the armrest (1) from the seat. NOTE : Make sure the seat is in the stowed position before you remove
____
the bolts (7).
(4)
In the cockpit, remove the bolts (3) and the washers (4) from the seat base (2).
EFF : ALL
25-11-51Page 402
May 01/05
R
CES
R R Captain Seat Figure 401/TASK 25-11-51-991-001-A
EFF : ALL 25-11-51 Page 403 Nov 01/00
CES
R R First Officer Seat Figure 402/TASK 25-11-51-991-002-A 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备1(103)
