EFF : ALL
25-22-41Page 408
Nov 01/98
R Restraint System Figure 404/TASK 25-22-41-991-004
EFF : ALL 25-22-41 Page 409 May 01/01
CES
TASK 25-22-41-400-001
Installation of the Wall-Mounted Cabin-Attendant Seats
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 08-065 USA MIL-T-60394 TYPE I CLASS I
DOUBLE SIDED ADHESIVE TAPE (Ref. 20-31-00)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
11-00-00-400-007 Installation of the ESSO (Scotchcal Labels)
24-42-00-861-001 Energize the Ground Service Network from the External Power
24-42-00-862-001 De-energize the Ground Service Network Supplied from
the External Power
AMM 11-32-25 P.Block 001 INTERIOR PLACARDS (SEE ALSO 11-42-25)
25-22-41-991-001 Fig. 401
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
25-22-41-991-002 Fig. 402
EFF : ALL
25-22-41Page 410
**ON A/C ALL
3. Job Set-up
__________
Subtask 25-22-41-860-050
A. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized (Ref. TASK 24-42-00-861-001).
(2)
Make sure that the stowage compartment of the seat is empty.
(3)
If you install a cabin-attendant seat which does not have a handset installed, continue from step 4. A.
Subtask 25-22-41-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-399,
49VU COM/CIDS/DEU B/ESS 153RH G03 **ON A/C 001-049, 051-099, 101-105, 201-299,
121VU COM NAV/CIDS/DEU B/NORM 162RH M07 R **ON A/C 106-149, 151-199, 401-499,
121VU COM NAV/CIDS/DEU B/NORM 162RH M08
EFF : ALL
25-22-41Page 411
**ON A/C ALL
4. Procedure
_________ Subtask 25-22-41-560-050
A. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that all of the placards of the retained/new components are in the correct position and in good condition.
(4)
If necessary install new placards (Ref. TASK 11-00-00-400-007) and (Ref. AMM 11-32-25 P.Block 001).
Subtask 25-22-41-420-050
B. Install the Single-Seat Assembly
(Ref. Fig. 401/TASK 25-22-41-991-001)
(1)
Install the washers (1) with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-065) to help the installation procedure.
(2)
Put the seat assembly (2) in position.
(3)
Install the washers (4) and the bolts (5).
(4)
If an electrical connector is installed, do these steps:
(a)
Remove the blanking caps from the electrical connectors.
(b)
Make sure that the electrical connectors are clean and in the correct condition.
(c)
Connect the electrical connector (7) to the electrical connector (8).
(5)
Install the removed equipment in the stowage.
(6)
Close the door (3).
(7)
Install the seat upholstery (6).
EFF : ALL
25-22-41Page 412
Aug 01/02
R
CES R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
Subtask 25-22-41-420-051
C. Install the Double-Seat Assembly
(Ref. Fig. 402/TASK 25-22-41-991-002)
(1)
Install the washers (1) with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-065) to help the installation procedure.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EQUIPMENT/FURNISHINGS 设备1(152)
