R Pressure Seal - Grommet Type - Cavity Arrangements ABS0717 Figure 001
20-43-41 Page 2
-Slide the accessories (threaded ring, backshell with strain-relief etc.) onto the cable harness.
-Cut the wires at right-angles.
____
NOTE : The wire cut must be clean without any protruding part or burns to avoid damage to the grommet of the pressure seal.
(b) Insertion of the electrical wires
-The tools and electrical wires must be clean and should be aligned with the axis of the hole during insertion to avoid damage to the grommet.
____
NOTE : Do not use lubricants for installation of the wires in the grommets.
-Insert the wires in the holes of the grommet. R - Slowly draw the wires through the pressure seal until they R reach their final position.
-The holes not used must be sealed with blind cables or sealing plugs.
-Install the accessories (threaded ring, backshell with strain-relief etc.) on the pressure seal.
20-43-41 Page 3
B. ABS0834
(1) P/N identification
ABS0834 - 24 - N 01
R | | | |
R | | | ------------ Part type code
R | | -------------- Finish code N = Nickel
R | ------------------ Shell size code
R --------------------------- Standard P/N
(2) P/N characteristics
(a) Temperature
Minimum operating temperature is : -55 deg.C (-67.00 deg.F).
Maximum operating temperature is : 200 deg.C (392.00 deg.F).
(b) Cavity arrangement code
(Ref. Fig. 002)
(3) Installation procedure
R
R (a) Preparation
R - Degrease and clean the surfaces using a lint face cloth and a
R small amount of cleaning agent (Material N.11-003).
R - Attach the pressure seal to the structure, paying attention to
R the direction of installation of the grommet.
R - Ensure that the O-ring is installed and make certain that this
R is positioned correctly in the groove.
R - Tighten the nut of the grommet between 1.23 m.daN (108.8495
R lbf.in) and 1.37 m.daN (10.1032 lbf.ft).
R - Slide the accessories (threaded ring, backshell with
R strain-relief etc.) onto the cable harness.
R (b) Insertion of the electrical wires
R - Cut the wires at right-angles.
R ____NOTE : The wire cut must be clean without any protruding part or
R burns to avoid damage to the grommet of the pressure seal.
R - Wrap tape around the end of the cable.
R - The tools and electrical wires must be clean and should be
R aligned with the axis of the hole during insertion to avoid
R damage to the grommet.
R ____NOTE : Do not use lubricants for installation of the wires in the
R grommets.
20-43-41 Page 4
R Pressure Seal - Grommet Type - Cavity Arrangement ABS0834 Figure 002
20-43-41 Page 520-43-41 Page 620-43-41 Page 7
- Insert the wire.
- Slowly draw the wire through the pressure seal until it reaches
its final position.
- Secure the cable with the cable tie so that the cable will not
move in the pressure seal.
- Inject compound (Material N. 09-002) around the base of the
wires.
- Clean off surplus sealant with solvent (Material N.11-003).
R
R (4) Wire addition procedure
- Clean and degrease the by-pass tube with solvent (Material
N.11-003).
- Wrap tape around the end of the wire.
- Insert the wire to be added in the by-pass tube.
- Slowly draw the wire through the by-pass tube until it reaches its
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 3(8)
