A320 ESPM Electrical Standard Practices Manual 3(13)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 -Seal the washer with adhesive tape and a thin bead of BONDING AND R ADHESIVE COMPOUNDS (Material No. 08-004) at the cables.
 -Put a temporary cable tie behind the plastic washer to hold the cables and prevent washer movement.
 -Let the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) dry.
 -Remove the colored cable tie at the bulkhead bearing face.
 -Make sure that the parts on which you must apply the SEALANTS (Material No. 09-052) or (Material No. 09-012E) are clean and dry.
 -Apply a small quantity of SEALANTS (Material No. 09-052) or (Material No. 09-012E) to the inner face of the pressure seal and to the cables.
 -Let it dry for 40 minutes to 90 minutes (Refer to the product data sheet).
 -Move the body of the pressure seal against the plastic washer.
 -Screw the coupling nut of the sheath on the pressure seal.
 -Put the pressure seal in vertical position.
 -Move the cables apart then fill with SEALANTS (Material No. 09-052) or (Material No. 09-012E) .
 -Hold the extrusion gun (SEMCO 650) nozzle constantly in contact with the compound surface.

20-43-42 Page 5

 Pressure Seal (Compound Filled) - Sealing Procedure ABS0122 R Figure 002

20-43-42 Page 6

 Pressure Seal (Compound Filled) - Sealing Procedure ABS0122 R Figure 003

20-43-42 Page 7

 Pressure Seal (Compound Filled) - Sealing Procedure ABS0122 R Figure 004

20-43-42 Page 820-43-42 Page 9

 - Squeeze the cables together with a cable tie.
 - Center the cables in the pressure seal.
 - Complete the filling operation.
 - Wait until SEALANTS (Material No. 09-052) or (Material No. 09-012E)
 is fully cured.
 - Loosen the coupling nut.
 - Remove the cable tie behind the washer.
 - Remove the plastic washer.
 - Remove any BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004)
 runs.
 - Remove any SEALANTS (Material No. 09-052) or (Material No. 09-012E)
 runs.
 - Screw the coupling nut of the sheath on the pressure seal. 
R  D. Associated items 
R  - Backshell ABS1365 and ABS1366 
R  (1) P/N Identification 
R  (Ref. Fig. 005) 
R  ABS1365 - 22 - 20 B 1 
R  ABS1366 - 22 - 24 B 1 
R  | | | | | 
R  | | | | ------ Pressure seal type code 
R  | | | --------- Harness protection code: B or C 
R  | | ------------- Conduit size code 
R  | ------------------ Shell size code 
R  ------------------------ Standard P/N 
R  (2) P/N Characteristics 
R  (a) Temperature 
R  Minimum operating temperature is -55 DEG.C (-67.00 DEG.F) 
R  Maximum operating temperature is 175 DEG.C (347.00 DEG.F) 
R  (b) Harness protection code 
R  (Ref. Fig. 005) 
R  ------------------------------------------------------------------
R  | Code | Harness protection | 
R  |---------|------------------------------------------------------| 
R  | B | Overbraiding | 
R  |---------|------------------------------------------------------| 
R  | C | Braided conduit used with ABS0887 convoluted conduit | 
R  ------------------------------------------------------------------

 

R Pressure Seal (Compound Filled) - P/N Characteristics R ABS1365 and 1366 R Figure 005

20-43-42 Page 1020-43-42 Page 11

 _________3. NSA934710
 A. P/N Identification NSA934710 T 11 | | | | | ------------- Type code | ------------------ Part code -------------------------- Standard P/N
 B. P/N Characteristics
 (1) Temperature Operating temperature is 105 DEG.C (221.00 DEG.F)
R  (2) Part code and type (Ref. Fig. 006) T = Seal E = Spring spacer
 C. Procedure
R R R R R R R R R  _______WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS ONLY WITH A GOOD FLOW OF AIR THROUGH THE WORK AREA. THESE MATERIALS ARE POISONOUS AND FLAMMABLE AND SKIN IRRITANTS. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1) Materials and tools - Adhesive tape (Not specific). - SEALANTS (Material No. 09-002) or (Material No. 09-016). - CLEANING AGENTS (Material No. 11-004A) or equivalent. - Extrusion gun : SEMCO model 650 or PYLES model 950. - Dia 4 mm (0.1574 in.) polyethylene nozzle. - SEMCO cartridge.
 (2) Preparation
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 3(13)