Splices - Stripping and Crimping Tools ABS0249 R Figure 001
20-43-11 Page 220-43-11 Page 3
R - Do the same procedure from step 2 for the other end of the splice.
R - Do a check to make sure that the splicing is correct.
R _____3. E0360
R A. P/N Identification
R E0360RK2220
R | |
R | | | R = Splice Code
R | | | K = Type
R | |------------- Reference N. | 22 = Sequence No.
R | | 20 = Size Code.
R |
R -------------------- Standard P/N
R B. P/N Characteristics
R ____NOTE : EO360 is an assembly which has:
R - 2 sleeves NSA937210MBXXXX
R - 1 splice NSA936812-XX
R Two types of splice barrels can be available.
R The installation is the same.
R (1) Temperature
R Minimum operating temperature is -55 deg.C (-67.00 deg.F).
R Maximum operating temperature is 260 deg.C (500.00 deg.F).
R C. Connection Procedure
R (Ref. Fig. 002)
R (1) Insulation
R - Do the insulation with the shrinkable sleeves delivered:
R Install these sleeves on the wires before stripping.
R Shrinking is made after crimping.
R (2) Wire stripping
R - Use the applicable tool.
R - Strip the wire to the length "A" .
R (3) Crimping
R (Ref. Fig. 003)
R - Use the applicable crimping tool related to the splice reference
R number.
R - Make sure that the insulation sleeves are on the wires.
R - Put one end of the splice in the crimping tool die.
R - Make sure that the splice is in the correct position against the
R positioner.
Butt Splices - P/N Characteristics and Tools E0360 R Figure 002
20-43-11 Page 4
Butt Splices - Crimping Tools E0360 R Figure 003
20-43-11 Page 520-43-11 Page 620-43-11 Page 7
R ____NOTE : Depending on the barrel type, the position against the
R positioner is not the same.
R - Close the crimping tool handles sufficiently to hold the splice in
R position but do not crimp at this stage.
R - Put the stripped end of the wire in the splice barrel.
R - Tightly hold the wire in the barrel.
R - Crimp the splice. To do this, fully close the tool handles until
R the safety ratchet releases.
R - Remove the splice from the crimping tool.
R - Do the same procedure from step 2 for the other end of the splice.
R ____NOTE : For barrel type 1 only, the second crimping operation must be
R done diametrically opposite to the first one.
R For barrel type 2, the two crimping operations must be along
R the brazing seam centerline and positioned on the same side.
R - Do a check to make sure that the splicing is correct.
R (4) Insulation sleeve shrinking
R - Put the sleeve 1 (the shorter sleeve) in the correct position on
R the splice.
R - Shrink the sleeve with the applicable tool.
R - Wait until the sleeve is cold.
R - Put the sleeve 2 (the longer sleeve) in the correct position on the
R splice.
R - Shrink the sleeve with the applicable tool.
R - Make sure that the sleeves are in the correct condition.
_____4. E0541
A. P/N Identification
E0541-10
R | |-----------Splice Size Code
|----------------Standard P/N
B. P/N Characteristics
R (Ref. Fig. 004)
(1) Temperature
Minimum operating temperature is -65 deg.C (-85.00 deg.F).
Maximum operating temperature is 150 deg.C (302.00 deg.F).
(2) Materials
R There are 1 type of splice validated :
- tin-plated splice
R
C. Connection Procedure
R
(1) Insulation
R
R - Put the shrinkable sleeve delivered on the wires before stripping.
Shrinking is done after crimping.
R - For E0807 WX26 cable, make sure that the heat shielded sleeve
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 ESPM Electrical Standard Practices Manual 3(2)
