(24) At station 158, attach the ground wires to the ground studs with the nuts (60), the lockwashers (65) and the washers (70). (Ref. Fig. 414/TASK 71-51-43-991-308)
WIRE GROUND
GD9951DC/1 GD9951DC GD9951DC/2 GD9951DC GD9952DC/1 GD9952DC GD9952DC/2 GD9952DC GD9953DC/1 GD9953DC GD9953DC/2 GD9953DC GD9954DC/1 GD9954DC GD9954DC/2 GD9954DC GD9955DC GD9955DC GD9956DC GD9956DC GD9957DC GD9957DC
NOTE : Make sure that the electrical resistance, from each ground
____ wire to the terminal stud, is not more than 0.0025 ohms.
(25) Put the harness (5) in the flip-lock clamp (30) and tighten the
captive screw.
F 『R EEFF : ALL E Page A46371-51-43
E E Feb 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(26) Connect the electrical connector 4007EN-A to the oil chip detector. (Ref. Fig. 415/TASK 71-51-43-991-309)
(27) Connect the electrical connector 4002EN-A to the oil quantity transmitter.
(28) Put the harness (5) into the rubber supports for line blocks (40) and (55).
(29) Make sure that the harness (5) is correctly installed on the engine.
(30) Put the rubber supports in the line blocks (40) at stations 191 and
199. Close the line blocks and tighten the captive bolts.
(31) Put the rubber supports in the line blocks (55) at station 199. Close the line blocks and tighten the captive bolts.
(32) Put the clamp (80) on the harness (5). Attach the clamp (80) to the bracket on station 199 with the bolt (75).
(33) TORQUE the bolt (75) to between 20 and 25 lbf.in (0.22 and 0.28 m.daN).
(34) Connect the electrical connector 4000KC-A to the high pressure fuel shutoff.
(35) Put the harness (5) into the rubber supports for line blocks (50) and (55).
(36) Make sure that the harness (5) is correctly installed on the engine.
(37) Put the rubber supports in the line blocks (50) and (55) along station 158. Close the line blocks and tighten the captive bolts.
(38) Put the harness (5) in the flip-lock clamp (105) and tighten the
captive screw. R R AFTER SPIB NO. CFM02255MW1 R (Ref. Fig. 414/TASK 71-51-43-991-308) R
R (39) Put the harness (5) into the rubber support of the line block (10)
R along the top left side of the engine.
R (Ref. Fig. 414/TASK 71-51-43-991-308)
R (40) Put the rubber support in the line block (10) at station 174.
F 『 EEFF : ALL E Page A46471-51-43
E E Feb 01/04 E E ECES ER (41) Install the clamps and bolt (17) that attach the harness (5) to the R bracket at station 176.
F 『
E C F M E
E E
E 56-5B E
E E
R (42) Install the clamps and bolt (22) that attach the harness (5) to the R bracket at station 185.
R (43) Put the harness into the flip-lock clamps (30) and (35) near station R 191.
R (44) Install the nuts, bolts and clamps (32) that attach the harness (5) R to the brackets at station 191.
R (45) Install the bolt and clamp (42) and (47) that attach the harness (5) R to the brackets at station 191.
R (46) At station 191, attach the ground wires to the ground studs with the R nuts (60), lockwashers (65) and washers (70). R (Ref. Fig. 414/TASK 71-51-43-991-308) R WIRE GROUND R R GD9958DC/1 GD9958DC R GD9958DC/2 GD9958DC R GD9959DC/1 GD9959DC R GD9959DC/2 GD9959DC R GD9960DC/1 GD9960DC R GD9960DC/2 GD9960DC R GD9961DC/1 GD9961DC R GD9961DC/2 GD9961DC R GD9962DC/1 GD9962DC R GD9962DC/2 GD9962DC R GD9963DC/1 GD9963DC R GD9963DC/2 GD9963DC R GD9964DC GD9964DC
R NOTE : Make sure that the electrical resistance, from each ground
____ R wire to the terminal stud, is not more than 0.0025 ohms.
R (47) Tighten the captive screws on flip-lock clamps (30) and (35) near R station 191.
R (48) Connect the electrical connector 4000EL-A to the fuel filter R differential pressure switch.
R (49) Connect the electrical connector 4003EN-A to the oil pressure R transmitter.
F 『 EEFF : ALL E Page A46571-51-43
E E Feb 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
R (50) Connect the electrical connector 4000EN-A to the low oil pressure
R switch.
R (51) Install the bolt and clamps and anti-rotation lug (57) that attach
R the harness (5) to the bracket at station 167.
R (Ref. Fig. 414/TASK 71-51-43-991-308)
R (52) Install the bolts, clamps and anti-rotation lug (43) that attach the
R harness (5) to the brackets at station 158.
R (53) Connect the electrical connector 1074GK-A or 3074GD-A, as applicable, 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM 动力装置 POWER PLANT 2(58)
