F 『
E C F M E
E E
E 56-5B E
E E
R (39) Install the clamps, bolt and anti-rotation lug (68) that attach the
R harness (5) to the bracket.
R (40) Install the clamp, bolt and anti-rotation lug (57) near the ignition
R exciter B.
R (41) Connect the electrical connector 4000JH2-A to the ignition exciter B.
R (42) Connect the electrical connectors 4000KS-J2 and 4000KS-J4 to the ECU.
R NOTE : The wire harness for connectors 4000KS-J4 and 4000KS-J6 may____
R touch as shown on
R (Ref. Fig. 409/TASK 71-51-43-991-314)
R (Detail B)
R (43) Install the clamps and bolts (62) that attach the harness (5) to the
R brackets at station 191.
R (44) Install the clamp and bolt (82) that attach the harness (5) to the
R bracket at station 191.
R (45) Put the harness (5) into the flip-lock clamp (55) attached to the
R bracket at station 191.
R (46) Install the clamp and bolt (57) that attach the harness (5) to the
R brackets at station 191.
R (47) TORQUE the bolts (22), (23), (27), (28), (32), (37), (57), (62),
R (67), (68) and (82) to between 25 and 30 lbf.in (0.28 and 0.33
R m.daN).
R
R END SPIB NO. CFM02255MW1
R
R (48) Connect the electrical connector 4000EV-C to the fan speed sensor
(N1).
PRE SB RA32171-6
R (49) Put the harness (5) into the flip-lock clamp (55) that is attached to
the bracket at station 185.
POST SB RA32171-6
R (50) Put the clamp (50) on the harness (5). Use the bolt (40) to attach
the clamp (50) to the bracket at station 185.
E E Feb 01/04 E E ECES E F 『 EEFF : ALL E Page 49771-51-43
F 『
E C F M E
E E
E 56-5B E
E E
R (51) TORQUE the bolt (40) to between 20 and 25 lbf.in (0.22 and 0.28 m.daN).
END SB RA32171-6
R (52) Put the two clamps (50) on the harness (5). Attach the clamps (50) to the starter bracket with the bolts (70) and nuts (75).
R (53) Put the clamp (50) on the harness (5). Use the bolt (40) and nut (45) to attach the clamp to the gearbox bracket.
R (54) Put the clamp (50) on the harness (5). Use the bolt (85) and nut (90) to attach the clamp (50) and the fire detector clamp to the gearbox bracket. (Ref. Fig. 409/TASK 71-51-43-991-314) (Detail C)
R (55) TORQUE the nuts (45), (80) and (90) to between 20 and 25 lbf.in (0.22 and 0.28 m.daN).
R (56) Connect the electrical connector 4001EV-C to the gas generator speed sensor (N2).
R (57) Tighten the captive screws on the flip-lock clamps.
R (58) Examine the harness installation and make sure that all flip-lock clamps, line blocks and clamps are installed correctly.
Subtask 71-51-43-865-073
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3DA1, 3DA2, 3DA3, 4DA1, 4DA2, 4DA3, 5DA1, 5DA2, 5DA3, 1DB1, 1DB2, 4DG1, 4DG2, 1JH, 3801GX, 3802GX, 3803GX, 7TU, 2RK, 4RK FOR 1000EM1 2KS1, 4KS1, 2JH1, 3JH1, 1WE1, 2WE1, 7WD1, 8WD1, 2XU1 FOR 1000EM2 2KS2, 4KS2, 2JH2, 3JH2, 1WE2, 2WE2, 7WD2, 8WD2, 2XU2
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM 动力装置 POWER PLANT 2(40)
