1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-51-00Page 21 1201-299, 301-399, 1Config-1 Aug 01/05 1 1 1CES 1
Steering System - Sensors
Figure 012
1EFF : 001-004, 051-054, 1 32-51-00Page 22 1 1 Config-1 Aug 01/05 1 1 1CES 1
(4) On the nose gear: (Ref. Fig. 008)
(a)
A steering actuating cylinder which is part of the nose gear structure. The cylinder drives the rotating tube via a rack-and-pinion assembly.
(b)
A hydraulic block attached to the rear of the nose gear strut includes: (Ref. Fig. 009)
-
a check valve which keeps the anti-shimmy accumulator pressurized,
-
a 40 micron filter,
-an electrically-operated selector valve and its slaved valve. When the selector valve is energized, the pressure is applied to the servovalve.
-a servovalve of the deflection-jet type, equipped with a LVDT sensor which detects the position of the slide valve,
-an adjustable diaphragm located on each output line of the servovalve, this diaphragm is used to adjust the flow to each actuating cylinder chamber and consequently the wheel steering speed,
-a by-pass valve which interconnects the two chambers of the steering cylinder in the event of hydraulic system depressurization which may be due to: the loss of hydraulic power or the de-energization of the selector valve by the monitoring channel or the de-energization of the selector valve by the towing control lever on the electrical box,
-when the hydraulic system is pressurized, the bypass valve can open for a pressure exceeding 273 bars. Any overpressure is then limited in the steering cylinder,
-an anti-shimmy accumulator with a built-in pressure-relief valve, It can supply fluid pressurized to 15 bars in case of cavitation in one chamber of the cylinder, initiated by the shimmy.
-two check valves which ensure the distribution of fluid from the accumulator to the chamber of the steering cylinder,
-a screw for the bleeding and/or depressurization of the hydraulic block,
(c)
Two anti-shimmy valves (one per chamber) are installed on the steering cylinder.
1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 23 1201-299, 301-399, 1Config-1 Aug 01/05 1 1 1CES 1
(d)
A swivel selector valve is installed co-axially with respect to the landing gear retraction axis. It provides the hydraulic interface between the aircraft and the landing gear. When the landing gear starts to retract, the swivel selector valve cuts the hydraulic power supply and connects the hydraulic block to the reservoir return line. (Ref. Fig. 010)
(e)
Two identical sensor boxes give the position of the rotating tube. The sensor box has a gear assembly with a sensor housing attached at the top by a clamping flange and four screws. The sensor box is shock-mounted to the landing gear strut. The sensor housing assembly contains an RVDT sensor. One sensor is part of the electrical channel of the steering control, the other sensor is part of the monitoring channel. These two sensors are supplied with 115 V from AC BUS 1 through the BSCU system 1.
The gear assembly contains:
-a reduction gear train
-for maintenance only: a knob with a lockpin to lock the reduction gear in the neutral position (0 degree) before installation of the sensor box on the landing gear a worm screw to adjust the electrical 0 degree position with the sensor box installed on the landing gear. (Ref. Fig. 011, 012A)
(f)
An electrical box with a towing control lever.
(g)
A pointer attached at the rear of the nose gear permits to put the nose wheels in the zero position. (Ref. Fig. 004)
(5) in the avionics compartment:
-a Braking and Steering Control Unit (BSCU) which groups the braking and steering computers.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
3. Interface
_________ (Ref. Fig. 011) The corresponding figure shows the electrical interface between the BSCU, the various system components and the ECAM.
1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-51-00Page 24 1201-299, 301-399, 1Config-1 Aug 01/05 1 1 1CES 1
Steering System - Sensors
Figure 012A
1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 25 1201-299, 301-399, 1Config-1 Aug 01/05 1 1 1CES 1
4. Component Description
_____________________
A. Steering Handwheel Transmitter Unit It includes two control potentiometers and two monitoring potentiometers, driven by different gears to permit the detection of any rupture of the control. The travel of each potentiometer is plus or minus 150 deg. (Ref. Fig. 013, 014)
B. Rudder pedals
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架8(70)
