B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-12-00-582-001 Jacking for Nose Gear Wheel Change 12-14-32-614-001 Nitrogen Filling of the Tires 32-49-15-991-002 Fig. 402
3. Job Set-up
__________ Subtask 32-49-15-941-051
A. Safety Precautions
(1)
In the cockpit, on the panel 400VU, put warning notice(s) in position to tell persons not to operate the landing gear control lever.
(2)
Put the safety barriers in position.
(3)
On the panel 110VU, make sure that the PARK BRK control switch is in the OFF position.
1EFF : 051-099, 1 32-49-15Page 409 1 1 May 01/05 1 1 1CES 1 Subtask 32-49-15-865-053
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/TIRE/PRESS 1GV M31
Subtask 32-49-15-860-051
C. Aircraft Maintenance Configuration
(1)
Install the chocks on the wheels of the main landing gear.
(2)
Lift the nose gear (Ref. TASK 07-12-00-582-001).
(3)
Fully deflate the tire (Ref. TASK 12-14-32-614-001).
4. Procedure
_________
(Ref. Fig. 402/TASK 32-49-15-991-002) Subtask 32-49-15-020-053
A. Removal of the Pressure Transducer Adaptor
(1)
Make sure that the tire is fully deflated.
(2)
Remove the cotter pin (5) and discard it.
(3)
Remove the nut (6).
(4)
Remove the pressure transducer (4).
(5)
Remove the pressure transducer adaptor (2).
1EFF : 051-099, 1 32-49-15Page 410 1 1 May 01/05 1 1 1CES 1
NLG-Tire Pressure-Transducer Adaptor
Figure 402/TASK 32-49-15-991-002
1EFF : 051-099, 1 32-49-15 Page 411
1 1 May 01/05
1 1
1CES 1
TASK 32-49-15-400-002
Installation of the NLG tire Pressure Transducer Adaptor
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice(s) No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
1 packing 32-49-15 01 -040 3 packings 32-49-15 01 -050 5 cotter pin 32-49-15 01 -010
1EFF : 051-099, 1 32-49-15Page 412 1 1 May 01/05 1 1 1CES 1
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-12-00-582-001 Jacking for Nose Gear Wheel Change 12-14-32-614-001 Nitrogen Filling of the Tires 32-49-00-720-001 Crosscheck TPIS Reading and Tire Pressure Gauge 32-49-15-991-002 Fig. 402
3. Job Set-up
__________ Subtask 32-49-15-860-055
A. Aircraft Maintenance Configuration
(1)
In the cockpit, on the panel 400VU, make sure that the warning notice(s) is (are) in position to tell persons not to operate the landing gear control lever.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架8(57)
