D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-12-00-582-001 Jacking for Nose Gear Wheel Change 12-14-32-614-001 Nitrogen Filling of the Tires 32-49-00-720-001 Crosscheck TPIS Reading and Tire Pressure Gauge 32-49-15-991-001 Fig. 401
3. Job Set-up
__________ Subtask 32-49-15-860-053
A. Aircraft Maintenance Configuration
(1)
In the cockpit, on the panel 400VU, make sure that the warning notice(s) is (are) in position to tell persons not to operate the landing gear control lever.
(2)
Make sure that safety barriers are in position.
(3)
Make sure that the PARK BRK control switch is in the OFF position.
(4)
Make sure that the chocks are installed on the wheels of the main landing gear.
(5)
Make sure that the nose gear is lifted (Ref. TASK 07-12-00-582-001).
(6)
Make sure that the tire is fully deflated (Ref. TASK 12-14-32-614-001).
Subtask 32-49-15-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/TIRE/PRESS 1GV M31
1EFF : 051-099, 1 32-49-15Page 406 1 1 May 01/05 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 401/TASK 32-49-15-991-001) Subtask 32-49-15-110-050
A. Preparation before Installation
(1)
Clean the shaft (2) with CLEANING AGENTS (Material No. 11-002). Dry it with clean, dry compressed air.
(2)
Apply a thin layer of COMMON GREASE (Material No. 04-004) to the shaft (2).
Subtask 32-49-15-420-052
B. Installation of the Pressure Transducer
(1)
Install the new preformed packing (3) on the shaft (2).
(2)
Install the pressure transducer (4) on the shaft (2). NOTE : Make sure that the pressure transducer (4) is in the correct
____
position.
(3)
Install the nut (6) and tighten it.
(4)
TORQUE the nut (6) to between 0.3 and 0.9 m.daN (26.54 and 79.64 lbf.in).
(5)
Safety the nut (6) with the cotter pin (5).
(6)
Install the grommet (11) on the cable of the pressure transducer (4).
(7)
Remove the blanking cap from the connector (12) and connect the electrical connector.
(8)
Install the grommet (11). Put the cover (7) in position.
Install the drive (8) in its housing.
(9)
Install the washers (10) and the screws (9).
(10)
Tighten the screws (9) and safety them with the corrosion resistant steel lockwire dia 0.8 mm (0.032 in.).
(11)
Inflate the tire (Ref. TASK 12-14-32-614-001).
1EFF : 051-099, 1 32-49-15Page 407 1 1 May 01/05 1 1 1CES 1 Subtask 32-49-15-865-052
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GV
Subtask 32-49-15-720-050
D. Functional Test
(1) Do the functional test of the Tire Pressure Indicating System (Ref. TASK 32-49-00-720-001).
5. Close-up
________ Subtask 32-49-15-860-052
A. Put the aircraft back to its initial configuration.
(1)
Lower the aircraft on its wheels (Ref. TASK 07-12-00-582-001).
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : 051-099, 1 32-49-15Page 408 1 1 May 01/05 1 1 1CES 1
TASK 32-49-15-000-002 Removal of the NLG Tire Pressure Transducer Adaptor WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架8(56)
