曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
NOTE-
1. On a standard day the Mach numbers equivalent to
250knots CAS (subject to minor variations) are:
FL 240-0.6
FL 250-0.61
FL 260-0.62
FL 270-0.64
FL 280-0.65
FL 290-0.66.
2. When an operational advantage will be realized, speeds
lower than the recommended minima may be applied.
2. To arriving turbojet aircraft operating below
10,000 feet:
(a) A speed not less than 210 knots, except;
(b) Within 20 flying miles of the airport of
intended landing, a speed not less than 170 knots.
3. To arriving reciprocating engine or turboprop
aircraft within 20 flying miles of the runway
threshold of the airport of intended landing, a speed
not less than 150 knots.
4. To departing aircraft:
(a) Turbojet aircraft, a speed not less than
230knots.
(b) Reciprocating engine aircraft, a speed not
less than 150 knots.
e. When ATC combines a speed adjustment with
a descent clearance, the sequence of delivery, with the
word “then” between, indicates the expected order of
execution.
EXAMPLE-
1. Descend and maintain (altitude); then, reduce speed to
(speed).
2. Reduce speed to (speed); then, descend and maintain
(altitude).
NOTEThe
maximum speeds below 10,000 feet as established in
14 CFR Section 91.117 still apply. If there is any doubt
concerning the manner in which such a clearance is to be
executed, request clarification from ATC.
f. If ATC determines (before an approach
clearance is issued) that it is no longer necessary to
apply speed adjustment procedures, they will inform
the pilot to resume normal speed. Approach
clearances supersede any prior speed adjustment
assignments, and pilots are expected to make their
own speed adjustments, as necessary, to complete the
approach. Under certain circumstances, however, it
may be necessary for ATC to issue further speed
adjustments after approach clearance is issued to
maintain separation between successive arrivals.
Under such circumstances, previously issued speed
adjustments will be restated if that speed is to be
maintained or additional speed adjustments are
requested. ATC must obtain pilot concurrence for
speed adjustments after approach clearances are
issued. Speed adjustments should not be assigned
inside the final approach fix on final or a point 5 miles
from the runway, whichever is closer to the runway.
NOTEAn
instruction to “resume normal speed” does not delete
speed restrictions that are contained in a published
procedure, unless specifically stated by ATC, nor does it
relieve the pilot of those speed restrictions which are
applicable to 14 CFR Section 91.117.
g. The pilots retain the prerogative of rejecting the
application of speed adjustment by ATC if the
minimum safe airspeed for any particular operation is
greater than the speed adjustment.
NOTEIn
such cases, pilots are expected to advise ATC of the
speed that will be used.
h. Pilots are reminded that they are responsible for
rejecting the application of speed adjustment by ATC
if, in their opinion, it will cause them to exceed the
maximum indicated airspeed prescribed by 14 CFR
Section91.117(a), (c) and (d). IN SUCH CASES,
THE PILOT IS EXPECTED TO SO INFORM ATC.
Pilots operating at or above 10,000 feet MSL who are
issued speed adjustments which exceed 250 knots
IAS and are subsequently cleared below 10,000 feet
MSL are expected to comply with 14 CFR
Section91.117(a).
i. Speed restrictions of 250 knots do not apply to
U.S. registered aircraft operating beyond 12 nautical
miles from the coastline within the U.S. Flight
Information Region, in Class E airspace below
10,000 feet MSL. However, in airspace underlying a
Class B airspace area designated for an airport, or in
a VFR corridor designated through such as a Class B
airspace area, pilots are expected to comply with the
200 knot speed limit specified in 14 CFR
Section91.117(c).
2/14/08 AIM
ATC Clearances and Aircraft Separation 4-4-9
j. For operations in a Class C and ClassD surface
area, ATC is authorized to request or approve a speed
greater than the maximum indicated airspeeds
prescribed for operation within that airspace (14 CFR
Section 91.117(b)).
NOTEPilots
are expected to comply with the maximum speed of
200 knots when operating beneath Class B airspace or in
a Class B VFR corridor (14 CFR Section 91.117(c)
and(d)).
k. When in communications with the ARTCC or
approach control facility, pilots should, as a good
operating practice, state any ATC assigned speed
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
航空信息手册2008上(137)
