(7)
Solvent - Butyl carbitol (alternative to B01011, Series 91) -commercially available (AMM 20-30-91/201)
(8)
Solvent - B01011, Series 91 - commercially available
(AMM 20-30-91/201)
(9)
Wiping cloth, lint-free - commercially available
(10)
Squeegee - commercially available
C.
References
(1)
AMM 36-00-00/201, Pneumatic - General
D.
Prepare for the Repair
S 862-081
(1) Release the pressure from the pneumatic system (AMM 36-00-00/201)
NOTE: This will make sure that there is no airflow in the ducts
____
when you do the repair.
S 862-082
(2)
On the bleed air control module on the pilots' overhead panel, P5, put the pack control switches in the OFF position.
S 012-084
(3)
Remove the applicable ceiling, sidewall, or floor panels to gain access to the damaged air conditioning duct.
S 012-085
(4)
If insulation is installed on the duct, remove the insulation.
S 342-086
(5)
Do these steps to prepare the damaged area of the duct.
WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON
_______ YOUR SKIN. DO NOT BREATHE THE FUMES FROM THE SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIRONMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
(a)
Use the solvent and a wiping cloth to clean the damaged area.
(b)
Drill a hole at each end of the cut or crack to prevent the cut or crack from getting larger. The holes should be a maximum of 1/16 inch diameter.
(c)
Sand the damaged area to remove any remaining adhesive and contamination.
(d)
Use the solvent and a wiping cloth to clean the damaged area.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-23-01
ALL ú ú 01 Page 206 ú May 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
S 342-087
(6)
Prepare the Fiberglass or Kevlar cloth.
(a)
Cut sufficient pieces of fiberglass or Kevlar cloth to equal the thickness of the duct.
(b)
Cut the fiberglass or Kevlar cloth pieces 1/2 inch larger on all sides than the damage.
(c)
Round the corners of the pieces of fiberglass or Kevlar cloth.
S 342-088
(7)
Prepare the applicable resin.
E.
Repair the Air Conditioning Duct
S 342-089
(1) Apply a thin, smooth layer of resin to the duct where the fiberglass or Kevlar cloth will be applied.
NOTE: Make sure the area of the resin is larger than the size and
____ shape of the fiberglass or Kevlar cloth pieces.
S 342-090
(2)
Put a piece of fiberglass or Kevlar cloth on the resin so that it extends beyond the cut or crack a minimum of 1/2 inch on all sides.
S 342-091
(3)
Soak the fiberglass or Kevlar cloth with the applicable resin.
S 342-092
(4)
Put a piece of plastic sheet on the fiberglass or Kevlar cloth and press lightly with a squeegee or with your hand. Make the fiberglass or Kevlar cloth smooth from the center to the edges of the cloth to remove any bubbles or any wrinkles and to remove unwanted resin.
S 342-093
(5)
Remove the plastic sheet from the fiberglass or Kevlar cloth and remove unwanted resin with a wiping cloth.
S 342-094
(6)
Put another piece of the fiberglass or Kevlar cloth on the first piece, soak it with resin, and make it smooth.
NOTE: Continue using the same procedure until the thickness of the
____
patch equals the thickness of the duct.
S 342-095
(7) Let the resin cure for 24 hours at room temperature.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-23-01
ALL ú ú 01 Page 207 ú May 28/00
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：757 AMM 飞机维护手册 空调 AIR CONDITIONING 1(30)
