(2) If the electrical connector 7527VC is OK:
- do a check and repair of the aircraft wiring from the ECB (59KD) AC/5,4 to the electrical connector 7527VCA/J,K and the ECB (59KD) AB/G2,G3,G4,G5 to the electrical connector 7527VCA/D,C,E,B and the electrical connector 7527VCA/A,L,F, to GND (Ref. ASM 49-61/01).
(a) If the aircraft wiring is OK:
- replace the AIR INTAKE FLAP ACTUATOR (4015KM) (Ref. AMM TASK 49-16-51-000-003) and (Ref. AMM TASK 49-16-51-400-003).
(b) If the fault continues:
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
R **ON A/C 001-049, 101-105, 107-107, 151-199, 201-210,
B. Do the test given in para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page 280
201-210, Config-1 Aug 01/05 CES
TASK 49-00-81-810-829
APU AUTO SHUTDOWN - HIGH OIL TEMPERATURE, High Oil Temperature (131-9(A))
1. Possible Causes
_______________
- NO LRU FAULT DETECTED
- blockage of the air intake duct
- blockage of the APU inlet housing
- OIL COOLER ducting
- OIL TEMPERATURE SENSOR
- OIL COOLER
- COOLING-FAN ASSEMBLY
- APU GENERATOR (8XS)
- OIL TEMPERATURE SENSOR (8092KM)
- OIL COOLER (8079KM)
- COOLING-FAN ASSEMBLY (8053KM)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 24-23-51-000-001 Removal of the APU Generator 8XS
AMM 24-23-51-400-001 Installation of the APU Generator 8XS
AMM 49-00-00-860-008 APU Start by External Power (131-9(A))
AMM 49-52-51-000-002 Removal of the Cooling Fan (8053KM) (131-9(A))
AMM 49-52-51-400-002 Installation of the Cooling Fan (8053KM) (131-9(A))
AMM 49-91-44-000-004 Removal of the Oil Cooler (8079KM) (131-9(A))
AMM 49-91-44-400-004 Installation of the Oil Cooler (8079KM) (131-9(A))
AMM 49-94-15-000-001 Removal of Oil Temperature Sensor (8092KM) (131-9(A))
AMM 49-94-15-400-001 Installation of Oil Temperature Sensor (8092KM)
(131-9(A))
3. Fault Confirmation
__________________
A. Read-out of ECB Trouble-Shooting Data
(1) Put the APU MASTER SW to the ON position.
(2) Get access to the APU SHUTDOWN report.
(3) Push the '>' adjacent to LRU DATA:
- the MCDU menu shows
NO LRU FAULT DETECTED
(4) Start the APU and apply Bleed Air for 20 seconds, minimum (Ref. AMM TASK 49-00-00-860-008).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page 281
201-210, Config-1 Aug 01/05 CES
4. Fault Isolation
_______________
R **ON A/C 001-049, 101-105, 107-107, 151-154, 201-207,
A. If an APU auto shutdown occurs during the APU operation and the APU SHUTDOWN report gives the maintenance message:
HIGH OIL TEMPERATURE
OIL COOLER/COOLING FAN ASSEMBLY
associated with the Fault Code Number (FCN) 211
- do a check for
blockage of the air intake duct
blockage of the APU inlet housing
OIL COOLER ducting for blockage or contamination.
(1) If there is no blockage or contamination:
- replace the OIL TEMPERATURE SENSOR (Ref. AMM TASK 49-94-15-000-001) and (Ref. AMM TASK 49-94-15-400-001).
(a) If the fault continues:
- do a replacement of the OIL COOLER (Ref. AMM TASK 49-91-44-000-004) and (Ref. AMM TASK 49-91-44-400-004).
(b) If the fault continues:
- replace the COOLING-FAN ASSEMBLY (Ref. AMM TASK 49-52-51-000-002) and (Ref. AMM TASK 49-52-51-400-002).
(c) If the fault continues:
- replace the APU GENERATOR (8XS) (Ref. AMM TASK 24-23-51-000-001) and (Ref. AMM TASK 24-23-51-400-001).
**ON A/C 001-049, 101-105, 151-199, 201-210,
Post SB 49-1062 For A/C 001-049,101-105,151-154,201-207,
A. If an APU auto shutdown occurs during the APU operation and the APU SHUTDOWN report gives the maintenance message:
HIGH OIL TEMPERATURE
OIL COOLER (8079KM) / COOLING FAN (8053KM)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 机载辅助动力 2(64)
