(4) If the MCDU menu shows:
LOW OIL PRESSURE SWITCH SHOWS OPEN CIRCUIT
- do the Fault Confirmation that follows:
(a) Get access to the APU TEST menu.
(b) Push the TEST line key.
4. Fault Isolation
_______________
R **ON A/C 001-049, 101-105, 107-107, 151-154, 201-207,
A. If the APU TEST menu gives the maintenance message:
LOW OIL PRESS SW P14
associated with Fault Code Number (FCN) 98
- do a check for damage/contamination of electrical connector P14 of the LOW OIL PRESSURE SWITCH (P14)
(1) If the electriacl connector P14 is damaged/contaminated:
- do a repair/cleaning.
(2) If the electrical connector is OK:
- use a multimeter to do a resistance check across pin 1 and pin 2 of the LOW OIL PRESSURE SWITCH (P14)
(a) If the resistance value is > 10 Ohms:
- replace the LOW OIL PRESSURE SWITCH (P14) (Ref. AMM TASK 49-23-51-000-004) and (Ref. AMM TASK 49-23-51-400-004).
(b) If the resistance value is < 10 Ohms:
- do a check and repair of the aircraft wiring from the ECB (59KD) AB/C5 to LOW OIL PRESSURE SWITCH (P14) P14/1 and the LOW OIL PRESSURE SWITCH (P14) P14/2 to GND (Ref. ASM 49-61/02).
1 If the fault continues:
_
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page B216
201-210, Config-1 Aug 01/05 CES
**ON A/C 001-049, 101-105, 151-199, 201-210,
Post SB 49-1062 For A/C 001-049,101-105,151-154,201-207,
A. If the APU TEST menu gives the maintenance message:
LOW OIL PRESS SW (8091KM)
associated with Fault Code Number (FCN) 98
- do a check for damage/contamination of electrical connector P14 of the LOW OIL PRESSURE SWITCH (8091KM)
(1) If the electriacl connector P14 is damaged/contaminated:
- do a repair/cleaning.
(2) If the electrical connector is OK:
- use a multimeter to do a resistance check across pin 1 and pin 2 of the LOW OIL PRESSURE SWITCH (8091KM)
(a) If the resistance value is > 10 Ohms:
- replace the LOW OIL PRESSURE SWITCH (8091KM) (Ref. AMM TASK 49-23-51-000-004) and (Ref. AMM TASK 49-23-51-400-004).
(b) If the resistance value is < 10 Ohms:
- do a check and repair of the aircraft wiring from the ECB (59KD) AB/C5 to LOW OIL PRESSURE SWITCH (8091KM) P14/1 and the LOW OIL PRESSURE SWITCH (8091KM) P14/2 to GND (Ref. ASM 49-61/02).
1 If the fault continues:
_
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
R **ON A/C 001-049, 101-105, 107-107, 151-199, 201-210,
B. Do a check of the APU TEST menu to verify the fault is not present.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page B217
201-210, Config-1 Aug 01/05 CES
TASK 49-00-81-810-869
Oil-Temperature Sensor (P11) Fault (131-9(A))
1. Possible Causes
_______________
- OIL TEMP SENSOR SHOWS OUT OF RANGE LOW
- OIL TEMP SENSOR SHOWS OUT OF RANGE HIGH
- damage/contamination of electrical connector P11
- OIL TEMPERATURE SENSOR (P11)
- aircraft wiring
- ECB (59KD)
- Oil Sump Temp Sensor (8084KM)
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific multimeter
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 49-61-34-000-003 Removal of the Electronic Control Box (ECB) (131-9(A)) AMM 49-61-34-400-003 Installation of the Electronic Control Box (ECB)
(131-9(A)) AMM 49-94-15-000-001 Removal of Oil Temperature Sensor (8092KM) (131-9(A)) AMM 49-94-15-400-001 Installation of Oil Temperature Sensor (8092KM)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 机载辅助动力 2(116)
