「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞24-20-00∞∞∞∞∞∞∞∞∞∞Page A288
Aug 01/05 CES
R 5. Close-up________
R A. Put the aircraft back to its initial configuration.
R (1) Stop the engine 1 (Ref. AMM TASK 71-00-00-710-028).
R (2) Do the EIS stop procedure
R (Ref. AMM TASK 31-60-00-860-002).
R (3) On the ECAM control panel, set the UPPER DISPLAY and LOWER DISPLAY
R potentiometers to OFF.
R (4) De-energize the aircraft electrical circuits
R (Ref. AMM TASK 24-41-00-862-002).
R TASK 24-20-00-810-881 R Failure of the Generator Control Unit 2 R 1. Possible Causes
_______________ R - GCU-2 (1XU2) R 2. Job Set-up Information
______________________
R A. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R AMM 24-22-34-000-001 R AMM 24-22-34-400-001 R AMM 24-41-00-740-002 R AMM 24-41-00-861-002 R R AMM 24-41-00-861-002 R R AMM 24-41-00-862-002 R R AMM 24-41-00-862-002 R R AMM 31-60-00-860-001 R AMM 31-60-00-860-002 R AMM 71-00-00-710-003 R AMM 71-00-00-710-028
R 3. Fault Confirmation
__________________
R A. Test Removal of the GCU-1(2) (1XU1, 1XU2) Installation of the GCU-1(2) (1XU1, 1XU2) Operational Check of GAPCU via CFDS Energize the Aircraft Electrical Circuits from the External Power Energize the Aircraft Electrical Circuits from the APU De-energize the Aircraft Electrical Circuits Supplied from the External Power De-energize the Aircraft Electrical Circuits Supplied from the APU EIS Start Procedure EIS Stop Procedure Engine Automatic Start Engine Shutdown
R (1) Remove all AC and DC power from the GCU 2:
R - de-energize the aircraft electrical circuits from the APU (Ref. AMM
R TASK 24-41-00-862-002),
R - de-energize the aircraft electrical circuits from the external
R power (Ref. AMM TASK 24-41-00-862-002),
R - disconnect the batteries or open the GCU 2 circuit breaker (2XU2)
R to remove the 28VDC backup power-supply from the GCU 2.
R (2) Apply power to the GCU 2:
R - energize the aircraft electrical circuits from the APU (Ref. AMM
R TASK 24-41-00-861-002),
R - energize the aircraft electrical circuits from the external power
R (Ref. AMM TASK 24-41-00-861-002).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞24-20-00∞∞∞∞∞∞∞∞∞∞Page A290
Aug 01/05 CES
R (3) Do the BITE test of the GAPCU (Ref. AMM TASK 24-41-00-740-002).
R (a) If the BITE test gives the message TEST FAILED:
R - push the line key adjacent to the TEST FAILED message.
R 1 If the maintenance message GCU2 (1XU2) comes into view:_
R - do the trouble shooting procedure given in Para 4.A.
R (b) If the BITE test gives the message TEST PASSED:
R - stop the trouble shooting.
R 4. Fault Isolation_______________
R A. If the BITE test gives the maintenance message GCU2 (1XU2) or if the APU
R generator or the external power do not energize the aircraft electrical
R circuits:
R - replace the GCU-2 (1XU2) (Ref. AMM TASK 24-22-34-000-001) and (Ref. AMM
R TASK 24-22-34-400-001).
R B. Do this operational test to make sure that the system operates correctly.
R (1) Aircraft Maintenance Configuration
R (a) Energize the aircraft electrical circuits
R (Ref. AMM TASK 24-41-00-861-002).
R (b) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only)
R (Ref. AMM TASK 31-60-00-860-001).
R (2) On the ELEC panel 35VU:
R - push, release and push again the GEN 2 pushbutton switch (3XU2).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 电源 2(24)
