_______________ R - IDG (4000XU) R 2. Job Set-up Information
______________________
R A. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R AMM 12-13-24-612-041 R R AMM 24-21-00-210-046 R R AMM 24-21-00-210-047 R R AMM 24-21-00-720-041 R R AMM 24-21-51-000-040 R R AMM 24-21-51-400-040 R R AMM 24-41-00-740-002 R AMM 24-41-00-861-002 R R AMM 24-41-00-862-002 R R AMM 31-60-00-860-001 R AMM 31-60-00-860-002 R AMM 71-00-00-710-003 R AMM 71-00-00-710-028
R 3. Fault Confirmation
__________________
R A. Test
R Not applicable.
IDG Servicing - Filling of the IDG with Oil or Addition of Oil after a Level Check Check of the Oil Level and Oil-Filter Differential-Pressure Indicator (DPI) Visual Inspection of the IDG for Oil Leaks and Check of the Electrical Circuits Operational Test of the IDG Disconnect and Reconnect (Reset) Function - Engine in Operation Removal of the Integrated Drive Generator -IDG 1(2),(4000XU) Installation of the Integrated Drive Generator -IDG 1(2),(4000XU) Operational Check of GAPCU via CFDS Energize the Aircraft Electrical Circuits from the External Power De-energize the Aircraft Electrical Circuits Supplied from the External Power EIS Start Procedure EIS Stop Procedure Engine Automatic Start Engine Shutdown
R NOTE : As the GEN 2 was set to OFF because of a true failure, the fault
____ R confirmation is not necessary.
R 4. Fault Isolation
_______________
R A. If the fault symptom is identified by the CFDS message IDG2 (E2-4000XU) R and the upper ECAM DU warning GEN 2 FAULT:
R NOTE : This CFDS message comes into view when a generator under-frequency
____ R trip occurs because of a low oil pressure in the IDG. It usually R comes into view with the CFDS message IDG2 (E2-4000XU) LOW OIL R PRESSURE.
R - do a check of the Differential Pressure Indicator (DPI) if the IDG 2
R (Ref. AMM TASK 24-21-00-210-046).
R (1) If the DPI is extended:
R - replace the engine 2 IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040)
R and (Ref. AMM TASK 24-21-51-400-040).
R (2) If the DPI is not extended:
R - do a check of the IDG 2 oil level (Ref. AMM TASK 24-21-00-210-046).
R (a) If the oil level is correct:
R - replace the engine 2 IDG (4000XU) (Ref. AMM TASK 24-21-51-000-R 040) and (Ref. AMM TASK 24-21-51-400-040).
R (b) If the oil level is low:
R - do a check of the IDG, the external oil-circuit tubing and the
R fuel/oil heat exchanger for oil leaks (Ref. AMM TASK 24-21-00-R 210-047).
R 1_ If there is leak:
R - repair the leak or replace the components as necessary
R - add oil (Ref. AMM TASK 12-13-24-612-041) and reconnect the
R IDG 2 (if disconnected).
R 2_ If there is no leak:
R - add oil (Ref. AMM TASK 12-13-24-612-041) and reconnect the
R IDG 2 (if disconnected)
R - do a dynamic disconnect test of the IDG 2 (Ref. AMM TASK 24-R 21-00-720-041).
R a_ If the oil pressure is correct:
R - stop the trouble shooting.
R b_ If the oil pressure is not correct:
R - replace the engine 2 IDG (4000XU) (Ref. AMM TASK 24-21-R 51-000-040) and (Ref. AMM TASK 24-21-51-400-040).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 260
Aug 01/05 CESR B. Do this operational test to make sure that the system operates correctly. R (1) Aircraft Maintenance Configuration R (a) Energize the aircraft electrical circuits
R (Ref. AMM TASK 24-41-00-861-002).
R (b) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only)
R (Ref. AMM TASK 31-60-00-860-001).
R (2) On the ELEC panel 35VU:
R - push, release and push again the GEN 2 pushbutton switch (3XU2).
R (3) Do the operational test of the GAPCU (Ref. AMM TASK 24-41-00-740-R 002).
R (4) Start the engine 2 (Ref. AMM TASK 71-00-00-710-003).
R (5) Do this test:
R -------------------------------------------------------------------------------
R ACTION RESULT
R -------------------------------------------------------------------------------R On the ECAM control panel: On the lower ECAM DU:
R - get the ELEC page. - the correct electrical parameters of
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 电源 2(118)
