c Use a sticker, tag or other method to write on the IDG that
_
you did the second or third reset of the DPI.
CES
TASK 24-21-00-810-817
Abnormal Oil Consumption of the IDG1 (2)
1. Possible Causes
_______________
- IDG (4000XU)
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific tube
No specific plastic container 1 l (0.2641 USgal)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 24-21-00-210-047
AMM 24-21-51-000-040
AMM 24-21-51-400-040
AMM 24-41-00-861-002
AMM 24-41-00-862-002
AMM 31-60-00-860-001
AMM 31-60-00-860-002
AMM 71-00-00-710-003
AMM 71-00-00-710-028
AMM 71-73-49-000-006
AMM 71-73-49-400-006
AMM 78-30-00-481-041
AMM 78-36-00-010-040
AMM 78-36-00-410-040
3. Fault Confirmation
__________________
A. Test Not applicableVisual Inspection of the IDG for Oil Leaks and Check of the Electrical CircuitsRemoval of the Integrated Drive Generator -IDG 1(2),(4000XU)Installation of the Integrated Drive Generator -IDG 1(2),(4000XU)Energize the Aircraft Electrical Circuits from the External PowerDe-energize the Aircraft Electrical Circuits Supplied from the External PowerEIS Start ProcedureEIS Stop ProcedureEngine Automatic StartEngine ShutdownRemoval of the Oil Tank Drain Tube and HoseInstallation of the Oil Tank Drain Tube and HoseMake the Thrust Reverser Unserviceable for MaintenanceOpening of the Thrust Reverser DoorsClosing of the Thrust Reverser Doors
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 235
Aug 01/05R
CES
4. Fault Isolation
_______________
A. Inspection
(1) Do a visual inspection of the IDG1 (2) and external system (tubings, cooler) for oil leaks (Ref. AMM TASK 24-21-00-210-047).
(2) If you find no leak continue the trouble shooting procedure as follows.
B. Aircraft Maintenance configuration
(1) Energize the aircraft electrical circuits (Ref. AMM TASK 24-41-00-861-002).
(2) Do the EIS start procedure (Ref. AMM TASK 31-60-00-860-001).
C. Check of the IDG Drain Mast for Leakage NOTE : An internal oil consumption of 1 cc is permitted for each flight
____
hour or when the engines operate.
(1) Preparation for the test
(a) Make the thrust reverser unserviceable for maintenance (Ref. AMM TASK 78-30-00-481-041).
(b) Open the thrust reverser doors (Ref. AMM TASK 78-36-00-010-040).
(c) On the engine drain collector assembly, put a plastic container and a tube on the IDG oil drain (Ref. AMM TASK 71-73-49-000-006) (Ref. AMM TASK 71-73-49-400-006).
(d) Close the thrust reverser doors (Ref. AMM TASK 78-36-00-410-040).
(2) Engine operation WARNING : - ENGINE OPERATION MUST NOT EXCEED MINIMUM IDLE WHEN
_______ PERSONNEL ARE IN ENTRY/EXIT CORRIDOR.
- POSITIVE COMMUNICATION BETWEEN THE FLIGHT COMPARTMENT AND PERSONNEL IN ENTRY EXIT CORRIDOR IS NECESSARY.
- INLET AND EXHAUST HAZARD AREAS MUST BE STRICTLY OBSERVED BY PERSONNEL IN ENTRY/EXIT CORRIDOR.
(a) Start the engine (Ref. AMM TASK 71-00-00-710-003) and let it become stable at minimum idle for 5 minutes.
(b) Operate the engine at 70 percent N1 and let it become stable for 5 minutes.
(c) Operate the engine at minimum idle and let it become stable for 5 minutes.
中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320 Trouble Shooting Manual 排故手册 电源 2(110)
