- if you did less than three resets: . do a check of the IDG1 oil filter(s) and the cover(s) for metal particles (Ref. AMM TASK 24-21-00-210-044).
1 If you find metal particles:
_
- replace the IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040) and (Ref. AMM TASK 24-21-51-400-040).
2 If you do not find metal particles:
_ a Drain the oil, replace the oil filter(s) and fill the IDG1
_ with oil (Ref. AMM TASK 24-21-00-920-040).
b Do a reset of the DPI.
_
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 230
Aug 01/05R CES
c Use a sticker, tag or other method to write on the IDG that
_
you did the second or third reset of the DPI.
CES
TASK 24-21-00-810-816
The Differential Pressure Indicator (DPI) of the IDG2 Oil Filter is Extended -
Alternate Procedure
1. Possible Causes
_______________
- IDG (4000XU)
- oil filter(s)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 24-21-00-210-044 Inspection of the Filter Element(s) AMM 24-21-00-920-040 Drain IDG Oil System, Discard Filter Element(s) and Replenish AMM 24-21-51-000-040 Removal of the Integrated Drive Generator -IDG 1(2),(4000XU) AMM 24-21-51-400-040 Installation of the Integrated Drive Generator -IDG 1(2),(4000XU) TSM 24-21-00 P.Block 301 INTEGRATED DRIVE GENERATOR SYSTEM (IDG, GCU)
3. Fault Confirmation
__________________
A. Test
Not applicable.
4. Fault Isolation
_______________
A. Do this trouble shooting procedure
NOTE : You can find the DPI extended with CFDS fault messages.
____ First, do the trouble shooting for each CFDS fault messages. For this, refer to the CFDS index list.
(1) If no message is found:
- replace the IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040) and (Ref.
AMM TASK 24-21-51-400-040), - or do the alternate procedure (IDG DPI reset).
B. Alternate Procedure (IDG DPI Reset)
NOTE : The alternate procedure lets you do a reset of a DPI as an
____
alternative to the replacement of the IDG.
There are conditions related to this procedure:
- A maximum of three resets is permitted.
- After a DPI reset, the DPI check interval becomes:
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 232
Aug 01/05R CES
. For normal operations: weekly or 100 FH (the one that comes
first).
. For Extended Range Twin-Engined Aircraft Operations (ETOPS):
before each flight.
If, after a DPI reset, the DPI does not extend again between two
scheduled oil/filter changes, you can cancel the conditions
related to this procedure:
- The DPI reset status goes back to zero (a maximum of three more resets is permitted).
- The DPI check interval goes back to the interval specified in the MPD. (Ref. TSM 24-21-00 P.Block 301)
(1) If this is the first reset:
(a) Do a check of the IDG2 oil filter(s) and the cover(s) for metal particles (Ref. AMM TASK 24-21-00-210-044):
1 If you find metal particles:
_
- replace the IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040) and (Ref. AMM TASK 24-21-51-400-040).
2 If yo do not find metal particles:
_ a Drain the oil, replace the oil filter(s) and fill the IDG2
_ with oil (Ref. AMM TASK 24-21-00-920-040).
b Do a reset the DPI.
_
c Use a sticker, tag or other method to write on the IDG that
_ you did the first reset of the DPI.
(2) If this is not the first reset:
(a) Do a check of the number of reset:
- if you did three resets: . replace the IDG (4000XU) (Ref. AMM TASK 24-21-51-000-040) and (Ref. AMM TASK 24-21-51-400-040).
- if you did less than three resets done: . do a check of the IDG2 oil filter(s) and the cover(s) for metal particles (Ref. AMM TASK 24-21-00-210-044).
1 If you find metal particles:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320 Trouble Shooting Manual 排故手册 电源 2(109)