R (Ref. AMM TASK 31-60-00-860-001).
R (2) On the ELEC panel 35VU:
R - push, release and push again the GEN 2 pushbutton switch (3XU2).
R (3) Do the operational test of the GAPCU (Ref. AMM TASK 24-41-00-740-
R 002).
R (4) Start the engine 2 (Ref. AMM TASK 71-00-00-710-003).
R **ON A/C ALL
C. Do this test:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the ECAM control panel: On the lower ECAM display unit:
- get the ELEC page. - the correct electrical parameters of GEN 2 are shown and AC 2 busbar is supplied by GEN 2.
5. Close-up
________
A. Put the aircraft back to its initial configuration.
(1) Stop the engine 2 (Ref. AMM TASK 71-00-00-710-028).
(2) On the ECAM control panel, set the UPPER DISPLAY and LOWER DISPLAY potentiometers to OFF.
(3) De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 292
Aug 01/05 CES
INTEGRATED DRIVE GENERATOR SYSTEM (IDG, GCU) - TASK SUPPORTING DATA
___________________________________________________________________
1. Interval DPI Check and Filter Replacement after DPI Reset
_________________________________________________________ This figure is not valable for the Extended Range Twin-Engined Aircraft Operations (ETOPS) (Ref. Fig. 301)
Interval DPI Check and Filter Replacement after DPI Reset
Figure 301
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-21-00∞∞∞∞∞∞∞∞∞∞Page 302
Feb 01/02 CES
AC MAIN GENERATION - FAULT ISOLATION PROCEDURES
_______________________________________________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
TASK 24-22-00-810-802
Difference in Current between the IDG 1 Current Transformer and the AC Current
Transformer 1
1. Possible Causes
_______________
- CT-AC, 1 (42XU1)
- CT-AC, 1 (42XU3)
- GCU-1 (1XU1)
- wiring
- 4000XU
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 24-21-51-000-040 Removal of the Integrated Drive Generator -IDG 1(2),(4000XU) AMM 24-21-51-400-040 Installation of the Integrated Drive Generator -IDG 1(2),(4000XU) AMM 24-22-17-000-001 Removal of the AC Current Transformers (41XU1, 41XU2, 42XU1, 42XU2, 42XU3 and 42XU4) AMM 24-22-17-400-001 Installation of the AC Current Transformers (41XU1,
41XU2, 42XU1, 42XU2, 42XU3 and 42XU4) AMM 24-22-34-000-001 Removal of the GCU-1(2) (1XU1, 1XU2) AMM 24-22-34-400-001 Installation of the GCU-1(2) (1XU1, 1XU2) AMM 24-41-00-740-002 Operational Test of the Ground power Control Unit
(GPCU)
ASM 24-22/01
3. Fault Confirmation
__________________
A. Test Do the operational test of the GPCU and do the check of class 3 faults of the GPCU from the CFDS (Ref. AMM TASK 24-41-00-740-002).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-22-00∞∞∞∞∞∞∞∞∞∞Page 201
Aug 01/05 CES
4. Fault Isolation
_______________
A. If the test gives the maintenance message CHECK GCU1 PIN B11D, B13D:
- do a check of the wiring for short to ground or open circuit between respectively: . the pin B/11D of the GCU 1 and the pin A/4 of each AC1 current transformer 42XU1 and 42XU3 . the pin B/13D of the GCU 1 and the pin A/1 of the IDG 1 (Ref. ASM 24-22/01).
(1) If the wiring is not correct:
- repair it.
(2) If the wiring is correct:
- do an impedance check of the internal wiring of the current transformers (42XU1 and 42XU3) between the pin A/4 and successively the pins A/1, A/2, A/3.
NOTE : The normal impedance is 10.15 Ohms plus or minus 3.45 Ohms.
____
- then do a check for insulation between the pin A/6 and successively the pins A/1, A/2, A/3, A/4.
(a) If the values are out of the specified tolerances:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 电源 2(130)
