(6)
Adjust the top, aft, vertical-roller (32), if:
-the friction load is more than 6.5 daN (14.6125 lbf) and/or
-the clearance is more than 0.25 mm (0.0098 in.).
**ON A/C ALL
Subtask 27-84-61-820-070
H. Adjustment of the Top, Aft Vertical-Roller R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 402/TASK 27-84-61-991-003-A)
**ON A/C 301-399,
(Ref. Fig. 402A/TASK 27-84-61-991-003)
**ON A/C ALL
(1)
Remove and discard the lockwire from the bolt (28).
(2)
Remove the bolt (28), the locking ring (29) and the locking plate (30).
(3)
Move the applicable track (1) through its full range of travel.
(4)
Adjust the eccentric bush (31) until the top, aft, vertical roller
(32) touches the track (1) at its highest point.
(5)
Apply a layer of SEALANTS (Material No. 09-018) or SEALANTS (Material No. 09-019) to the shank of the bolt (28).
(6)
Install the locking plate (30) and the locking ring (29) with the bolt (28).
(7)
Safety the bolt (28) with MISCELLANEOUS (Material No. 19-010).
(8)
Apply a layer of STORAGE PRESERVATION (Material No. 15-005) to the bolt (28), the locking ring (29) and the locking plate (30).
**ON A/C 001-049, 051-061, 101-105, 201-203,
Subtask 27-84-61-820-072
J. Adjustment of the Front Stop (Ref. Fig. 402/TASK 27-84-61-991-003-A, 404/TASK 27-84-61-991-002)
(1)
Remove and discard the lockwire from the bolts (15) and the applicable stop (14).
(2)
Remove the bolts (15) and the applicable front stop (14).
(3)
Apply a layer of SEALANTS (Material No. 09-018) or SEALANTS (Material No. 09-019) to the shanks of the bolts (15).
(4)
Loosely assemble the applicable stop (14) with the bolts (15).
(5)
Put and hold the track (1) in its fully retracted position.
(6)
Put the front stop (14) in position so that it is parallel with the bottom, forward, vertical-roller (32) and tighten the bolts (15).
(7)
Safety the bolts (15) with MISCELLANEOUS (Material No. 19-010).
(8)
Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to the bolts (15).
R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
Subtask 27-84-61-820-072-A
J. Adjustment of the Front Stop (Tracks 2 thru 4) R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,
(Ref. Fig. 402/TASK 27-84-61-991-003-A)
**ON A/C 301-399,
(Ref. Fig. 402A/TASK 27-84-61-991-003)
Slat-Track End-Stop - Location and Detail
Figure 404/TASK 27-84-61-991-002
R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 27-84-61Page 425 1 1 May 01/05 1 1 1CES 1R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 404A/TASK 27-84-61-991-002-A)
(1)
Remove and discard the lockwire from the bolts (15) and the applicable stop (14).
(2)
Remove the bolts (15) and the applicable front stop (14).
(3)
Apply a layer of SEALANTS (Material No. 09-018) or SEALANTS (Material No. 09-019) to the shanks of the bolts (15).
(4)
Loosely assemble the applicable stop (14) with the bolts (15).
(5)
Put and hold the track (1) in its fully retracted position.
(6)
Put the front stop (14) in position so that it is parallel with the bottom, forward, vertical-roller (32) and tighten the bolts (15).
(7)
Safety the bolts (15) with MISCELLANEOUS (Material No. 19-010).
(8)
Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to the bolts (15).
**ON A/C ALL
Subtask 27-84-61-640-062
K. Lubrication
(1) Lubricate the side-rollers (25) and the top and bottom, vertical-rollers (33) with COMMON GREASE (Material No. 04-024).
5. Close-up
________
Subtask 27-84-61-410-058
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
For the tracks 2 and 3, install the actuators (Ref. TASK 27-84-48-400-001).
Slat-Track End-Stop - Location and Detail Figure 404A/TASK 27-84-61-991-002-A
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-84-61Page 427 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(3) Install the applicable access panels:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵8(66)
