(12)
Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
1EFF : 001-049, 052-061, 101-105, 201-203, 1 27-84-63Page 426 1 1 Aug 01/05R 1 1 1CES 1
R (13) Apply special materials:
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______
R MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
R DO NOT BREATHE THE GAS.
R THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT.
R GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R (a) Apply SEALANTS (Material No. 09-001) to:
R - the nuts (4), (6), (18), (19), (20), (31), (32) and (42)
R - the bolt heads (11), (12), (15), (16), (17), (37), (39) and
R (41)
R - the locking plates (13) and (38).
R (14) Remove the BLOCK-SLAT GAPPING from the No. 9 slat track.
R (15) Do a check of the slat lower trailing-edge, dimension L:
R (a) Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT,
R installed outboard of the removed torque shaft FIN 6010CM(6060CM)
R (Ref. TASK 27-50-00-000-003).
R (b) Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND FLAP)
R to fully retract the slats.
R (c) Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
R outboard of the removed torque shaft FIN 6010CM(6060CM)
R (Ref. TASK 27-50-00-400-003).
R (d) Measure the dimension L of the slat lower trailing-edge. The
R dimension L must be 5 mm (0.1968 in.) +/- 2 mm (0.0787 in.) at
R all points along the length of the slat.
R (Ref. Fig. 405/TASK 27-84-63-991-004)
R (e) The slat lower trailing-edge must not be more than 1 mm (0.0393
R in.) into-wind or out-of-wind.
R NOTE : The dimension L and the into-wind and out-of-wind____
R dimensions are not adjustable. If the dimensions you
R measure are out of limits, you must tell the design
R authority at Airbus Industrie.
R 1EFF : 001-049, 052-061, 101-105, 201-203, 1 27-84-63Page 427 1 1 May 01/05 1 1 1CES 1
R (16) Install and adjust the closing plates (9) and (35) (Ref. TASK 27-84-
69-400-001).
R **ON A/C 051-051,
R Subtask 27-84-63-820-055-B
R C. Adjustment of the Slat
R (Ref. Fig. 401/TASK 27-84-63-991-001, 402/TASK 27-84-63-991-002, 403/TASK
R 27-84-63-991-003, 405/TASK 27-84-63-991-004)
R (1) Install the BLOCK-SLAT GAPPING (98D27804020000) at the No. 9 slat
R track.
R (2) Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT,
R installed outboard of the removed torque shaft FIN 6010CM(6060CM)
R (Ref. TASK 27-50-00-000-003).
R (3) Use the ADAPTOR-DRIVE, SLAT (AND FLAP) to retract the slats until
R they are approximately 50.8 mm (2.0000 in.) +/- 6.35 mm (0.2500 in.)
R from the BLOCK-SLAT GAPPING.
R (4) Use the BAR-TURNING (98D27804011000) to slowly retract the slats
R until the BLOCK-SLAT GAPPING touches the bottom roller at the No. 9
R slat track.
R (5) Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
R outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK
R 27-50-00-400-003).
R (6) Adjust the eccentric bushes (10) and (36) at the No. 1, 2, 3 and 4
R slat tracks to get dimension J. Refer to the table that follows.
R
R NOTE : Measure dimension J above the applicable slat track.____
R -------------------------------------------------------------------------------
R | TRACK | DIMENSION J | MAXIMUM ADJUSTMENT BECAUSE OF |
R | NO. | | LOCKING PLATE INSTALLATION |
R -------------------------------------------------------------------------------
R | 1 | 4.75 mm (0.187 in.) | + 0.25 mm (0.01 in.) - 0.25 mm (0.01 in.) |
R | 2 | 5.00 mm (0.196 in.) | + 0.25 mm (0.01 in.) - 0.25 mm (0.01 in.) |
R | 3 | 6.50 mm (0.255 in.) | + 0.25 mm (0.01 in.) - 0.25 mm (0.01 in.) |
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵8(120)
