(h)
Apply special materials:
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER
_______ SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
1 Apply SEALANTS (Material No. 09-001) to:
_
-
the nuts (3), (5), (17), (18) and (19)
-
the bolt heads (10), (11), (14), (15) and (16)
-
the locking plate (12).
(i) Remove the BLOCK-SLAT GAPPING from the No. 9 slat track.
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-84-63Page 433 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(j) Do a check of the slat lower trailing-edge, dimension L:
1 Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
_ PIVOT, installed outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-000-003).
2 Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND
_ FLAP) to fully retract the slats.
3 Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
_ PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
4 Measure the dimension L of the slat lower trailing-edge. The
_ dimension L must be 5 mm (0.1968 in.) +/- 2 mm (0.0787 in.) at all points along the length of the slat. (Ref. Fig. 405/TASK 27-84-63-991-004)
5 The slat lower trailing-edge must not be more than 1 mm
_ (0.0393 in.) into-wind or out-of-wind.
NOTE : The dimension L and the into-wind and out-of-wind
____ dimensions are not adjustable. If the dimensions you measure are out of limits, you must tell the design authority at Airbus Industrie.
(k) Install and adjust the closing plate (8) (Ref. TASK 27-84-69-400-001).
**ON A/C ALL
Subtask 27-84-63-820-059
D. Adjustment of the Seals after Installation of a New Slat
(Ref. Fig. 404/TASK 27-84-63-991-005)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
1EFF : ALL 1 27-84-63Page 434 1 1 May 01/05R 1 1 1CES 1
(1)
Remove the screws (51) and (54), the washers (53), the support
assembly (56) and the seals (52) and (55).
(2)
Apply a layer of SEALANTS (Material No. 09-016) to the screws (51)
and (54).
(3)
While the sealant is still wet, install the seals (52) and (55) and the support assemblies (53) and (56) with the screws (51) and (54) and the washers (53). Tighten the screws (51) and (54) by hand.
(4)
Adjust the seal (52) to touch the wing root over its full length.
(5)
Adjust the seal (55) until the Dim 'S' is 2 mm (0.0787 in.) +- 0.5 mm (0.0196 in.) over its full length.
(6)
Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT,
installed outboard of the removed torque shaft FIN 6010CM(6060CM)
(Ref. TASK 27-50-00-000-003).
(7)
Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND FLAP)
(98D27804001000) to slowly manually retract the slats to the zero
position.
(8)
Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT,
outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK
27-50-00-400-003).
(9)
Make sure that the seal (52) touches the wing root over its full
length.
(10)
Make sure that there is still a clearance between the seal (55) and the pylon structure over its full length.
(11)
If the position of the seal(s) (52) and/or (55) is not correct, do the adjustment procedure again.
(12)
When the adjustment is correct, remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT, installed outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-000-003).
(13)
Use the pneumatic wrench and the ADAPTOR-DRIVE, SLAT (AND FLAP) (98D27804001000) to manually extend the slats to the fully extended position.
(14)
Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵8(123)
