27-84-63-991-001 Fig. 401
**ON A/C 001-049, 051-061, 101-105, 201-203,
27-84-63-991-002 Fig. 402
R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
27-84-63-991-002-A Fig. 402A
**ON A/C ALL
27-84-63-991-003 Fig. 403
3. Job Set-up__________
R
Subtask 27-84-63-941-050
A. Safety Precautions
(1) Put the safety barriers in position.
R
R (2) Fully retract the slats (Ref. TASK 27-80-00-866-005).
R (3) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001)
R on the flap/slat control lever on panel 114VU.
R (4) Put a warning notice in the cockpit to tell persons not to operate
R the slat controls.
Subtask 27-84-63-860-054
R B. Aircraft Maintenance Configuration
R (1) Energize the ground service network
R (Ref. TASK 24-42-00-861-001).
R (2) On the MCDU:
R (a) Get access to the SYSTEM REPORT/TEST F/CTL page (Ref. TASK 31-32-
R 00-860-006).
R -------------------------------------------------------------------------------
R ACTION RESULT
R -------------------------------------------------------------------------------
R 1. On MCDU: On the MCDU:
R - push the line key for <SFCC1 - the MCDU shows the SFCC1 menu page 1.
R
R 2. Push the NEXT PAGE button - the MCDU shows the SFCC1 menu page 2.
R
R 3. Push the line key (2L) SYSTEM - the MCDU shows the slat SYSTEM DATA
R DATA SLT> submenu.
R -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R 4. Push the line key (1L) <PPU - the MCDU shows the PPU DATA page(s).
R R R R 5. Write down the APPU and the FPPU angles (deg) shown on the display or push (in) the line key PRINT > to get a print out of the screen.
R R (3) De-energize the ground service network (Ref. TASK 24-42-00-862-001).
R R (4) Remove the safety collar from the circuit breakers 9CV and 11CV.
Subtask 27-84-63-865-050
R C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06
Subtask 27-84-63-010-051
R D. Get Access
R (1) Put the adjustable access platform below the zone 510(610).
R R R (2) Remove the applicable access panel (Ref. TASK 57-41-37-000-006): - for the left wing, remove 522NB - for the right wing, remove 622NB.
R (3) Remove the applicable torque shaft (Ref. TASK 27-84-45-000-004): - for the left wing, remove FIN 6010CM - for the right wing, remove FIN 6060CM.
R (4) Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT, installed outboard of the removed torque shaft FIN 6010CM (6060CM) (Ref. TASK 27-50-00-000-003).
R 1EFF : ALL 1 27-84-63Page 404 1 1 Nov 01/03 1 1 1CES 1
(5) Install the ADAPTOR-DRIVE, SLAT (AND FLAP) (98D27804001000) and a pneumatic wrench or a wrench and socket on the applicable bevel gearbox:
-
for the left wing, use FIN 6010CM
-
for the right wing, use FIN 6060CM.
NOTE : This will let you operate the slats manually.
____
(6)
Manually extend the slats to the fully extended position
(7)
Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT outboard of the removed torque shaft FIN 6010CM(6060CM) (Ref. TASK 27-50-00-400-003).
(8) Remove the slat track closing plates (Ref. TASK 27-84-69-000-001). Subtask 27-84-63-480-051
E. Installation of Support Equipment
(1) Install the SLING-SLATS (98D27804009001) (Ref. TASK 27-80-00-400-001).
4. Procedure
_________
(Ref. Fig. 401/TASK 27-84-63-991-001)
**ON A/C 001-049, 051-061, 101-105, 201-203,
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵8(114)
