Subtask 27-84-45-865-057
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
Subtask 27-84-45-010-059
D. Get Access
(1)
Put the access platform in position below the applicable access panel:
(2)
Remove the applicable access panels:
-
FOR 6034CM
remove 522FB, 522HB, 522JB, 522KB
-
FOR 6084CM
remove 622FB, 622HB, 622JB, 622KB.
1EFF : ALL 1 27-84-45Page A407 1 1 Feb 01/00R 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 401/TASK 27-84-45-991-001, 403/TASK 27-84-45-991-003) Subtask 27-84-45-020-061
A. Removal of the Torque Shafts 6034CM(6084CM)
(1)
Install a LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001) (Ref. TASK 27-50-00-400-003): - on the torque shaft, inboard of the applicable components - on the torque shaft, outboard of the applicable components.
(2)
Remove the nuts (36) and (38), the bolts (37) and (39) and the shaft (29).
(3)
Remove the nuts (32), the bolts (31) and then the shaft (30).
(4)
Remove the universal joint (28).
(5)
Remove the retaining ring (34), the pin (33) and the universal joint (35).
1EFF : ALL 1 27-84-45Page A408 1 1 Feb 01/00R 1 1 1CES 1
TASK 27-84-45-400-013
Installation of the Torque Shaft 6034CM(6084CM)
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) 98D27504030001 2 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-018
GENERAL PURPOSE ASSEMBLY PASTE (Ref. 20-31-00)
Material No. 04-022 USA MIL-PRF-81322 GRADE 2
SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 11-026 GB DEF-STAN 68-148/1 R SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 15-007 AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R
R R R
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-000-003 Removal of the Lock-Torque Shaft - Flaps and Slats (98D27504030001) 27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and
Slats (98D27504030001) 27-80-00-866-005 Retracting the Slats on the Ground 27-84-00-710-001 Operational Test of the Slat System 27-84-45-991-001 Fig. 401 27-84-45-991-002 Fig. 402
3. Job Set-up
__________
(Ref. Fig. 401/TASK 27-84-45-991-001)
Subtask 27-84-45-941-069
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position to tell persons not to operate the slat controls.
Subtask 27-84-45-860-062
B. Aircraft Maintenance Configuration
(1)
Make sure that the access platform is in position below the applicable access panel.
(2)
Make sure that the applicable access panels have been removed:
-
FOR 6034CM
panels 522FB, 522HB, 522JB, 522KB
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵8(14)
