R **ON A/C ALL
5. Close-up
________
Subtask 27-54-62-410-059
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Connect the joints at tracks 3 and 4 to connect the actuator levers to the drive struts (Ref. TASK 27-54-55-400-002) and (Ref. TASK 27-54-55-400-003).
Subtask 27-54-62-942-058
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
ROLLER ASSY - FLAP GUIDE - REMOVAL/INSTALLATION
_______________________________________________
TASK 27-54-63-000-001
Removal of the Flap Guide-Roller Assembly
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific access platform 3.5 m (11 ft. 6 in.)
98D27504005000 1 PIN RIGGING-FLAPS (TRACK 1)
R 98D27504006000 1 PIN RIGGING FLAPS 98D27604000000 1 COLLAR-SAFETY, SPOILER 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-009 Retraction of the Flaps on the Ground
27-60-00-866-002 Extension-Retraction of the Spoilers for Maintenance R 57-51-37-000-004 Removal of the Access Panels R 575AB/575BB/575CB/575DB/575EB/575FB/575GB/575HB R (675AB/675BB/675CB/675DB/675EB/675FB/675GB/675HB)
27-54-63-991-001 Fig. 401
3. Job Set-up
__________
(Ref. Fig. 401/TASK 27-54-63-991-001)
Subtask 27-54-63-941-052
A. Safety Precautions
(1) Put a warning notice in position to tell persons not to operate the flight controls.
(2) Put the safety barriers in position.
Subtask 27-54-63-860-051
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Retract the flaps fully (Ref. TASK 27-50-00-866-009).
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat lever on panel 114VU.
Flap Guide - Roller Assembly
Figure 401/TASK 27-54-63-991-001
1EFF : ALL 1 27-54-63 Page 403
1 1 Feb 01/98
1 1
1CES 1
Subtask 27-54-63-865-050
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499, 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵6(90)
