(4)
Do a check of the flap rigged position (Ref. TASK 27-51-00-820-003).
(5)
At the track 1 position:
(a) TORQUE the nut (9) to between 0.8 and 1.2 m.daN (70.79 and 106.19 lbf.in) and safety with a new cotter pin (10).
(6)
At the track 2 position:
(a) TORQUE the nut (30) to between 10 and 12 m.daN (73.74 and 88.49 lbf.ft) and safety with a new cotter pin (29).
(7)
At tracks 1 and 2:
(a) Apply STORAGE PRESERVATION (Material No. 15-007) to the bolts (3) and (33) and the nuts (9) and (30) after assembly.
(8)
Install the Flap Track 2 actuator 6211CM(6261CM) (Ref. TASK 27-54-49-400-002).
(9)
Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT from the torque shaft outboard of the Track 2 actuator (Ref. TASK 27-50-00-000-003).
(10) Remove the hoisting sling (Ref. TASK 27-50-00-000-002).
R 1EFF : 301-399, 1 27-54-55Page 457 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
Subtask 27-54-55-865-054
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 27-54-55-710-050
E. Test
(1)
Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control-lever.
(2)
Do an operational test of the flaps (Ref. TASK 27-54-00-710-001).
(3)
Visually examine the inboard flap for correct operation during the retraction and extension of the flaps.
5. Close-up
________ Subtask 27-54-55-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels (Ref. TASK 53-35-11-000-001):
-
for the left wing, panel 193AB, 193BB
-
for the right wing, panel 194AB, 194BB.
(3)
Close the applicable MLG door (Ref. TASK 32-12-00-410-001).
(4)
Install the applicable access panel 573BB or 673BB (Ref. TASK 57-51-37-400-002).
1EFF : ALL 1 27-54-55Page 458 1 1 Aug 01/05R 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-54-55-860-057
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Fully retract the flaps (Ref. TASK 27-50-00-866-009).
(2)
Remove the COLLAR-SAFETY, SPOILER from the piston rod of the servo-control.
(3)
Fully retract the No. 1 Spoiler (Ref. TASK 27-60-00-866-002).
(a) On the servo-control, make sure that the pointer on the hex. head is opposite the letter 'O' (Operation) on the housing.
(4)
Install the No. 2 Flap-Track movable fairing (Ref. TASK 57-55-11-400-001).
**ON A/C 301-399,
Subtask 27-54-55-860-057-A
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Fully retract the flaps (Ref. TASK 27-50-00-866-009).
(2)
Remove the COLLAR-SAFETY, SPOILER from the piston rod of the servo-control.
(3)
Fully retract the No. 1 Spoiler (Ref. TASK 27-60-00-866-002).
(a) On the servo-control, make sure that the pointer on the hex. head is opposite the letter 'O' (Operation) on the housing.
(4)
Install the No. 2 Flap-Track movable fairing (Ref. TASK 57-55-11-400-004).
**ON A/C ALL
Subtask 27-54-55-942-052
C. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : ALL 1 27-54-55Page 460 1 1 Aug 01/05 1 1 1CES 1 TASK 27-54-55-000-002
Removal of the Flap-Actuator Lever Assembly - Track 3
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
