D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
20-28-00-912-004 Electrical Bonding of Components With Conductive
Bolts and Screws and Bonding Straps in the Fuselage
and in the Wings (this does not include the tanks)-
27-50-00-000-002 Removal of the Inboard and Outboard Flap
Hoisting-Sling
27-50-00-400-002 Installation of the Inboard and Outboard Flap
Hoisting-Sling
27-50-00-866-008 Extension of the Flaps on the Ground
27-50-00-866-012 Manual Retraction of the Flaps
27-51-00-820-003 To Do a Check of the Flap Rigged Position (With the
Sharks Fin)
27-51-00-820-009 Adjustment of the Flap Rigged Position With the
Sharks Fin Tool (A321)
27-51-44-000-001 Removal of the Interconnecting Strut
27-51-44-400-001 Installation of the Interconnecting Strut
27-54-00-710-001 Operational Test of the Flap System
27-54-41-000-001 Removal of the Right Angle Gearbox 6203CM,(6253CM)
27-54-41-400-001 Installation of the Right Angle Gearbox
6203CM,(6253CM)
27-54-61-000-002 Removal of the Flap Kink-Seals
27-54-61-400-006 Installation of the Flap Kink-Seals
27-54-63-000-001 Removal of the Flap Guide-Roller Assembly
27-54-63-400-001 Installation of the Flap Guide-Roller Assembly
27-60-00-866-002 Extension-Retraction of the Spoilers for Maintenance
27-64-00-710-001 Operational Test of the Spoiler Hydraulic Actuation
27-64-00-820-001 Adjustment of the Spoilers
57-55-11-010-002 To Lower the Flap Track No. 3 & No. 4 Movable
Fairings for Access
57-55-11-410-002 To Lift the Flap Track No. 3 & No. 4 Movable Fairings
after Access
27-54-62-991-021 Fig. 409
27-54-62-991-022 Fig. 410
27-54-62-991-023 Fig. 411
27-54-62-991-038 Fig. 412
27-54-62-991-039 Fig. 413
27-54-62-991-024 Fig. 415
27-54-62-991-025 Fig. 416
27-54-62-991-030 Fig. 417
27-54-62-991-027 Fig. 418
27-54-62-991-028 Fig. 419
27-54-62-991-033 Fig. 420
1EFF : 301-399, 1 27-54-62Page 454 1 1 May 01/05R 1 1 1CES 1
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-54-62-991-042 Fig. 421 27-54-62-991-045 Fig. 422
3. Job Set-up
__________ Subtask 27-54-62-941-061
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position on panel 400VU to tell persons not to operate the landing gear.
(3)
Make sure that the warning notice is in position on panel 114VU to tell persons not to operate the flight controls.
Subtask 27-54-62-865-055
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
Subtask 27-54-62-860-061
C. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Make sure that the access platform is in position below the applicable outboard flap.
(2)
Make sure that the applicable access panels are removed:
-
for the left wing, panels 573CB, 575AB and 575BB
-
for the right wing, panels 673CB, 675AB and 675BB.
1EFF : 301-399, 1 27-54-62Page 455 1 1 May 01/05R 1 1 1CES 1
(3)
Make sure that the applicable torque shaft has been disconnected from the right angle gearbox (Ref. TASK 27-54-41-000-001).
(4)
Make sure that the ADAPTOR-DRIVE, SLAT (AND FLAP) is installed on the right angle gearbox.
(5)
Make sure that the applicable spoilers 2, 3, 4 and 5 are fully extended and locked.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵6(71)
