(i)
Install the EXTRACTOR - PIN TRACKS 2 AND 3 (98D27504083000) and the EXTRACTOR - PIN (98D27504084000) to the carriage bolts (150). (Ref. Fig. 417/TASK 27-54-62-991-030)
NOTE : Make sure that you screw the extractor tools fully on to
____
the threads.
(j)
Remove the carriage bolts (150). If necessary, carefully lift the flap with the hoist and sling sufficiently to release the weight off the bolts (150).
(k)
Remove the splined bushes (140).
(3) Remove the flap from the wing: CAUTION : MAKE SURE THAT THE FLAP DOES NOT HIT THE AIRCRAFT
_______
STRUCTURE.
CAUTION : MAKE SURE THAT THE SUPPORT STRUCTURE IS CLEAN AND DOES NOT
_______
HAVE ANY SHARP POINTS.
(a)
Carefully and slowly lift the outboard flap off the flap track carriages.
(b)
Move the outboard flap with the hoist and lower it onto the support structure.
(4) Put covers, where necessary, over the disconnected items of the flap. Subtask 27-54-62-080-051
B. Removal of Equipment
(1) If necessary, remove:
-
the hoisting sling from the outboard flap (Ref. TASK 27-50-00-000-002)
-
the ADAPTOR-DRIVE, SLAT (AND FLAP) from the right angle gearbox
-
the EXTRACTOR - PIN TRACKS 2 AND 3 and EXTRACTOR - PIN from the carriage bolts (150). (Ref. Fig. 417/TASK 27-54-62-991-030)
1EFF : 301-399, 1 27-54-62Page 450 1 1 May 01/05R 1 1 1CES 1
Flap Removal and Installation Tools
Figure 417/TASK 27-54-62-991-030
1EFF : 301-399, 1 27-54-62 Page 451
1 1 May 01/05
1R 1
1CES 1
TASK 27-54-62-400-002
Installation of the Outboard Double-Slotted Flap
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific adhesive tape
No specific safety barriers
No specific warning notice
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft) 98D27504083000 1 EXTRACTOR - PIN TRACKS 2 AND 3 98D27504084000 1 EXTRACTOR - PIN 98D27504115000 2 DISTANCE GAUGES 98D27504118000 1 SPANNER-FLAP ADJUST 98D27504119000 1 SPANNER-FLAP ADJUST 98D27804001000 1 ADAPTOR-DRIVE, SLAT (AND FLAP) B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-022 USA MIL-PRF-81322 GRADE 2 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE (Ref. 20-31-00)
Material No. 09-002 USA MIL-S-8802 TYPE I CLASS B FUEL TANK SEALANTPOLYSULFID(NO LONGER AVAILABLE (Ref. 20-31-00)
Material No. 11-026 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 15-007 AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
Material No. 19-010 USA AMS 5687 LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
18 cotter pin 57-53-23 13 -140 21 spacer(s) 57-52-23 03 -360 24 cotter pin 57-52-23 03 -360 41 cotter pin 27-54-46 24 -095 46 cotter pin 57-53-23 10 -070 69 cotter pin 57-53-23 11 -070 127 cotter pin (127). 27-54-05 32A-040 127 cotter pin 27-54-05 32A-090 142 crushable washer 27-54-46 24 -030 142 crushable washer 27-54-46 26 -030 144 cotter pin 27-54-46 24 -010 144 cotter pin 27-54-46 26 -010
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵6(70)
