• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-21 14:21来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 27-54-55-860-058
 B. Aircraft Maintenance Configuration
 (1)
 Make sure that the flaps are fully extended (Ref. TASK 27-50-00-866-008).

 (2)
 Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control-lever.

 (3)
 Make sure that the Nos 2, 3, 4 and 5 spoilers are fully extended (Ref. TASK 27-60-00-866-002).

 (4)
 Make sure that the COLLAR-SAFETY, SPOILER is on the piston rod of the servo-control.

 (5)
 Make sure that the access platform is below the applicable zone 575 or 675.

 (6)
 Make sure that the access panels have been removed (Ref. TASK 57-51-37-000-004):

 -
for the left wing, 575BB and 575FB

 -
for the right wing, 675BB and 675FB.

 

 (7)
 Make sure that the No. 3 and No. 4 Flap Track movable fairings have been removed (Ref. TASK 57-55-11-000-001).

 (8)
 Make sure that the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT is installed on the torque shafts each side of the Track 3 actuator (Ref. TASK 27-50-00-400-003).

 (9)
 Make sure that the Track 3 actuator has been removed (Ref. TASK 27-54-49-000-003).

 


 **ON A/C 301-399,
 Subtask 27-54-55-860-058-A
 B. Aircraft Maintenance Configuration
 (1)
 Make sure that the flaps are fully extended (Ref. TASK 27-50-00-866-008).

 (2)
 Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control-lever.

 (3)
 Make sure that the No 2, 3, 4 and 5 spoilers are fully extended (Ref. TASK 27-60-00-866-002)

 (4)
 Make sure that the COLLAR-SAFETY, SPOILER is on the piston rod of the servo-control.

 (5)
 Make sure that the access platform is below the applicable zone 575 or 675.

 (6)
 Make sure that the access panels have been removed (Ref. TASK 57-51-37-000-004):

 -
for the left wing, 575BB and 575FB

 -
for the right wing, 675BB and 675FB.

 

 (7)
 Make sure that the No. 3 and No. 4 Flap Track movable fairings have been removed (Ref. TASK 57-55-11-000-004).

 (8)
 Make sure that the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT is installed on the torque shafts each side of the Track 3 actuator (Ref. TASK 27-50-00-400-003).

 (9)
 Make sure that the Track 3 actuator has been removed (Ref. TASK 27-54-49-000-003).


 1EFF : ALL 1 27-54-55Page 474 1 1 Aug 01/05R 1 1 1CES 1


 **ON A/C ALL
 Subtask 27-54-55-865-055
 C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
 4. Procedure
_________
 (Ref. Fig. 403/TASK 27-54-55-991-002)
 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210, 301-399,
 (Ref. Fig. 404/TASK 27-54-55-991-003)

R **ON A/C 106-149, 211-299, 401-499,
 (Ref. Fig. 404A/TASK 27-54-55-991-003-A)
 **ON A/C ALL
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
 EDGE:

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.


 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 Subtask 27-54-55-420-056
 A. Preparation for Installation
 (1)
 Remove the unwanted sealant from all the interface surfaces with a spatula that is not metal and with CLEANING AGENTS (Material No. 11-026).

 (2)
 Clean the component interface and/or the adjacent area with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 Examine the bushes and bearing surfaces for wear and for general condition.

 


 Subtask 27-54-55-914-054
 B. Application of Special Materials
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵6(7)