If the spoiler is safetied with ABS 0738 nuts, do the steps that follow:
(2) Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to the eye-end (8) on the rounded surface only.
NOTE : Do not get Material 15-007 on the servo control spherical
____
bearing.
Subtask 27-64-43-420-051
D. Installation of the Spoiler 3
CAUTION : SUPPORT THE SERVO CONTROL 7.5kg (16.5lb) AND THE SPOILER
_______ APPROXIMATELY 15kg (33lb). THIS WILL PREVENT DAMAGE TO:
-
THE HYDRAULIC LINES
-
THE ELECTRICAL CABLES
-THE STRUCTURE. If the spoiler is safetied with STA-LOK nuts, do the steps that follow:
(1)
Install the sliding bushes (25), (31), (36) and (37) in the rear spar fittings.
(2)
Make sure the spoiler 3 is held on supports. Push the spoiler forward and outboard to engage it on the hinge shaft.
(3)
Install the hinge pins (24), (30) and (38) through the rear spar fittings and the spoiler fittings.
(4)
Install the flanged bush (5) in the spoiler fitting.
(5)
Lift the spoiler actuator and hold it in the correct position so that the greaser on the eye-end (6) points down.
R 1EFF : 001-003, 051-052, 1 27-64-43Page 421 1 1 May 01/05 1 1 1CES 1
(6)
Install the hinge pin (4) through the flanged bush (5) and the
actuator eye-end (6).
(7)
Install the sliding bush (3) on the hinge pin (4) and make sure that it engages correctly in the spoiler fitting.
(8)
Install the STA-LOK nuts and washers (Ref. TASK 20-22-00-400-001).
(a)
Install the STA-LOK nut (2) with the WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-315-7500).
(b)
TORQUE the nut (2) to between 4.7 and 6.5 m.daN (34.66 and 47.93 lbf.ft).
(c)
Install the STA-LOK nuts (26) and (46) with the WRENCHES -NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-315-5000).
(d)
TORQUE the nuts (26) and (46) to between 2.0 and 3.4 m.daN (14.74 and 25.07 lbf.ft).
(e)
Install the STA-LOK nuts (32) and (35) with the WRENCHES -NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-315-6250).
(f)
TORQUE the nuts (32) and (35) to between 3.1 and 4.6 m.daN (22.86 and 33.92 lbf.ft).
(g)
Install the STA-LOK washer (1) with the TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454 (SL90-313-7500) on the hinge pin (4).
(h)
Install the STA-LOK washers (27) and (45) with the TOOL -INSTALLATION, TAB WASHER STA-LOK NSA5454 (SL90-313-5000) on the hinge pin (24) and the hinge shaft.
(i)
Install the STA-LOK washers (33) and (34) with the TOOL-INSTALLATION, TAB WASHERS STA-LOK NSA5454 (SL90-313-6250) on the hinge pins (30) and (38).
(9)
Clean the interfaces of the bolt (20) and the spacer (21) with a
clean MISCELLANEOUS (Material No. 19-003) and CLEANING AGENTS
(Material No. 11-026).
(10)
Apply a thin layer of SEALANTS (Material No. 09-018) or SEALANTS (Material No. 09-019) to the interfaces of the bolt (20) and the spacer (21).
(11)
Install the bolt (20) and the spacer (21).
R 1EFF : 001-003, 051-052, 1 27-64-43Page 422 1 1 May 01/05 1 1 1CES 1
(12)
Install the locking plates (23), (29) and (39) and then attach them with the nuts (22), (28) and (40).
(13)
TORQUE the nuts (22), (28) and (40) to between 0.25 and 0.30 m.daN
(22.12 and 26.54 lbf.in).
(14)
Attach the bonding straps (42) to each end of the spoiler with the bolts (41), the washers (44) and the nuts (43) (Ref. TASK 20-28-00-912-004).
If the spoiler is safetied with ABS 0738 nuts, do the steps that follow:
(15)
Install the sliding bushes (24), (33), (42) and (43) in the rear spar fittings.
(16)
Make sure the spoiler 3 is held on supports. Push the spoiler forward and outboard to engage it on the hinge shaft.
(17)
Install the hinge pins (23), (32) and (44) through the rear spar
fittings and the spoiler fittings.
(18)
Install the flanged bush (7) in the spoiler fitting.
(19)
Lift the spoiler actuator and hold it in the correct position so that the greaser on the eye-end (8) points down.
(20)
Install the hinge pin (6) through the flanged bush (7) and the
actuator eye-end (8).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵6(155)
