U. Adjust the Wing to Fuselage Panels
(Ref. Fig. 401A/TASK 27-54-61-991-001-A)
(1) Measure the dimension X, this must be between 23.5 mm (0.9251 in.) and 22.5 mm (0.8858 in.).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-61Page 451 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(2)
Measure the dimension U, this must be between 33.5 mm (1.3188 in.) and 32.5 mm (1.2795 in.).
(3)
If the dimension X is not correct loosen the screws (5) and move the aft seal until the dimension X is correct.
(4)
If the dimension U is not correct, loosen the screws (4) and move the forward seal until the dimension U is correct.
(5)
TORQUE the applicable screws (4) and/or (5) to between 0.4 and 0.45 m.daN (35.39 and 39.82 lbf.in).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-54-61-865-060
V. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 27-54-61-710-050
W. Test
(1)
Do an operational test of the flap system (Ref. TASK 27-54-00-710-001).
(2)
Do an operational test of the spoiler system (Ref. TASK 27-64-00-710-001).
5. Close-up
________
Subtask 27-54-61-942-051
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the access platform(s).
(4)
Close the MLG doors (Ref. TASK 32-12-00-410-001).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-61Page 452 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(5) Remove the ground support and maintenance equipment, the special and
standard tools and all other items.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-61Page 453 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL
TASK 27-54-61-000-002 Removal of the Flap Kink-Seals WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice
1EFF : ALL 1 27-54-61Page 454 1 1 Aug 01/05R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground
27-50-00-866-009 Retraction of the Flaps on the Ground
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
27-54-61-991-003 Fig. 409
**ON A/C 301-399,
27-54-61-991-003-A Fig. 409A R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
27-54-61-991-002 Fig. 410
**ON A/C 301-399,
27-54-61-991-002-A Fig. 410A
**ON A/C ALL
3. Job Set-up
__________
Subtask 27-54-61-941-059
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put the warning notice in position in the cockpit to tell persons not to operate the flight controls.
Subtask 27-54-61-860-061
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵6(30)
