(2)
Put the ACCESS PLATFORM 2M (6 FT) in position at the zone 132.
(a) Open the access door 825.
(3)
Put the ACCESS PLATFORM 2M (6 FT) in position at the zone 154.
(a) Open the access door 826.
(4)
Put the ACCESS PLATFORM 2M (6 FT) in position at the zone 312.
(a) Open the access door 312AR.
(5)
In the zones 211 and 221, remove the floor panels 211GF, 211KF, 221EF 221LF (Ref. TASK 53-12-11-000-001) and (Ref. TASK 53-12-12-000-001).
R 1EFF : 001-049, 054-099, 101-149, 151-199, 1 27-41-00Page 604 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R R R (6) In the zones 231 and 241, remove the floor panels 231CF, 231WF, 241BF, 241FF, 241KF (Ref. TASK 53-12-12-000-001) (Ref. TASK 53-22-12-000-001) (Ref. TASK 53-32-12-000-002).
R R (7) In the zone 131, remove the ceiling panels 131AC, 131BC, 131CC (Ref. TASK 25-54-12-000-002).
R R (8) In the zone 131, remove the partition panel 131PW (Ref. TASK 25-54-12-000-001).
R R R (9) In the zones 151 and 161, remove the ceiling panels 151AC, 151BC, 151CC, 151DC, 161AC, 161BC (Ref. TASK 25-55-11-000-002) (Ref. TASK 25-55-12-000-002).
R R (10) In the zone 161, remove the partition panels 161DW, 162DW (Ref. TASK 25-55-12-000-001).
**ON A/C ALL
4. Procedure_________
Subtask 27-41-00-210-050
A. Visual Inspection of the THS Mechanical Control (between FR8 and FR71)
(1) Make sure that all the nuts and the bolts are tight or safetied at each attachment point.
(2) Make sure that there is no corrosion on the bolts, the nuts and the washers.
(3) Make sure that the identification plates of all the components are attached correctly.
(4) Make sure that the front chain and the cable move freely.
(5) Make sure that the front chain and the cable do not touch the structure.
(6) Make sure that the cables are not damaged (Ref. TASK 20-24-12-200-001)
(7) Make sure that there is no corrosion on the cables (Ref. TASK 20-24-11-100-001).
Subtask 27-41-00-210-058
B. Visual inspection of the Rear THS Control Cable (between FR71 and the THS actuator) (Ref. Fig. 601/TASK 27-41-00-991-010)
(1)
Removal of the Protective Covers
(a)
Remove the screws (4) and the washers (3).
(b)
Release the fasteners (1) and remove the protective covers (2) and (5).
(2)
Do an inspection of the THS control cable between the tension regulator and the chain linkage.
(3)
Make sure that the chain and the cable move freely.
(4)
Make sure that the chain and the cable do not touch the structure (no marks on the fasteners).
(5)
Make sure that the chain that controls the THS actuator is in the correct condition.
(6)
Make sure that the cables are not damaged (Ref. TASK 20-24-12-200-001).
(7)
Make sure that there is no corrosion on the cables (Ref. TASK 20-24-11-100-001).
(8)
Installation of the Protective Covers
(a)
Install the protective covers (2) and (5).
(b)
Tighten the fasteners (1).
(c)
Install the washers (3) and the screws (4).
1EFF : ALL 1 27-41-00Page 606 1 1 May 01/05R 1 1 1CES 1
Removal/Installation of the Protective Covers. Figure 601/TASK 27-41-00-991-010
1EFF : 1 1R 1CES ALL 1 11 1 27-41-00 Page 607 May 01/05
5. Close-up
________ R **ON A/C 001-003, 051-053,
Subtask 27-41-00-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
In the zones 211 and 221, install the floor panels 211GF, 211KF, 221AF, 221EF (Ref. TASK 53-12-11-400-001) (Ref. TASK 53-12-12-400-001).
(3)
In the zones 231 and 241, install the floor panels 231CF, 231WF, 241BF, 241FF, 241KF (Ref. TASK 53-22-12-400-001) (Ref. TASK 53-32-12-400-002).
(4)
In the zone 131, install the ceiling panels 131AC, 131BC, 131CC (Ref. TASK 25-54-12-400-002).
(5)
In the zone 131, install the partition panel 131PW (Ref. TASK 25-54-12-400-001).
(6)
In the zones 151 and 161, install the ceiling panels 151AC, 151BC, 151CC, 151DC, 161AC, 161BC. (Ref. TASK 25-55-11-400-002) (Ref. TASK 25-55-12-400-002).
(7)
In the zone 161, install the partition panels 161DW, 162DW (Ref. TASK 25-55-12-400-001).
(8)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵3(95)
