A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵3(54)_航空信息_民用航空_通用航空

曝光台注意防骗网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

Subtask 27-34-41-865-051
F. Close Circuit Breakers
(1) Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3, 21CE1, 21CE2, 21CE3, 22CE
Subtask 27-34-41-720-050
G. Test
(1)
Install the GAUGE-ELEVATOR NEUTRAL SETTING (98D27309006000) and verify the elevator neutral position, (Ref. TASK 27-34-00-820-003).

(2)
Do an operational test of the elevators (Ref. TASK 27-34-00-710-001).

ELEVATOR - INSPECTION/CHECK
___________________________
TASK 27-34-41-200-001
Inspection/Check of the Elevator

1.
Reason for the Job

__________________
Self Explanatory

2.
Job Set-up Information

______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-34-41-000-001 Removal of the Elevator 27-34-41-400-001 Installation of the Elevator R CMM 552115PB601 27-34-41-991-005 Fig. 601
3. Job Set-up
__________
Subtask 27-34-41-010-051

A. Get Access
(1) Remove the aplicable elevator (Ref. TASK 27-34-41-000-001)
4. Procedure
_________
(Ref. Fig. 601/TASK 27-34-41-991-005)
Subtask 27-34-41-220-050

A. Fits and Clearances
(1) Complete an inspection of these dimensions,

Elevator Fits and Clearances
Figure 601/TASK 27-34-41-991-005
1EFF : ALL 1 27-34-41 Page 602
1 1 May 01/99
1 1
1CES 1

-------------------------------------------------------------------------------
| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | B | 7.912 | 7.924 | | | 7.899 | | | | OD 3 |(0.3114) |(0.3119) | | |(0.3109) | | | | | | | 0.001 | 0.025 | | | 0.051 | | | | | (0.0000*| (0.0009*| | |(0.0020*| | B | 7.925 | 7.937 | | | | 7.950 | | | ID 1 |(0.3120) |(0.3124) | | | |(0.3129) | | ********** DIFFERENCE IN IN. MARKED BY A STAR IS TRUNCATED **********
Subtask 27-34-41-220-051
B. Fits and Clearances
(1) Complete an inspection of these dimensions,
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | B | 10.989 | 11.000 | | | 10.974 | | | | OD 1 |(0.4326) |(0.4330) | | |(0.4320) | | | | | | | 0.000 | 0.029 | | | 0.059 | | | | | (0.0000)| (0.0011)| | |(0.0023)| | B | 11.000 | 11.018 | | | | 11.033 | | | ID 2 |(0.4330) |(0.4337) | | | |(0.4343) | | -------------------------------------------------------------------------------
Subtask 27-34-41-220-052
C. Fits and Clearances
(1) Complete an inspection of these dimensions,