(2)
Disconnect the elevator position transducer (Ref. TASK 27-92-13-000-001)
(3)
Disconnect the elevator servo control units (elevator side). (Ref. TASK 27-34-51-000-001)
NOTE : : Make sure that the harness connectors 49CE1, 49CE2 are
____ disconnected before removing the servo control units.
(4)
Disconnect the elevator from the elevator hinge fitting No. 4.
(a)
Disconnect the elevator support strut (16). (Ref. TASK 55-16-48-000-001).
(b)
Remove the sleeve (17). NOTE : Make sure that the slevee (17) is remove from the hinge
____ fitting before you remove the elevator. Damage can occur.
(c)
Remove and discard the cotter pin (6).
(d)
Remove the bolt (5) and the bush (4) from the hinge support.
(5)
Disconnect the elevator from the elevator hinge fittings No. 1, 2, 3, 5 and 6.
(a)
Remove and discard the cotter pin (9).
(b)
Remove the nut (7).
(c)
Remove and discard the cotter pins (6).
(d)
Remove the bolts (5) and the bushes (4) from all the hinge supports.
R 1EFF : 001-049, 052-099, 101-149, 151-199, 1 27-34-41Page 409 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(e) Carefully remove the elevator from the hinge arms and lower it
onto a correct support.
R **ON A/C 051-051,
R Subtask 27-34-41-020-053-A
R A. Removal of the Elevator
R (1) Disconnect the bonding straps (elevator side).
R (a) Remove the nuts (18), the washers (20) and the bolts (21) and
R disconnect the bonding straps (19).
R (2) Disconnect the elevator position transducer (Ref. TASK 27-92-13-000-
R 001)
R (3) Disconnect the elevator servo control units (elevator side).
R (Ref. TASK 27-34-51-000-001)
R NOTE : : Make sure that the harness connectors 49CE1, 49CE2 are____
R disconnected before removing the servo control units.
R (4) Remove the elevator and hinge fitting No. 4
R (a) Disconnect the elevator support strut (16). (Ref. TASK 55-16-48-
R 000-001).
R (b) Remove the sleeve (17).
R NOTE : Make sure that the sleeve (17) is removed from the hinge____
R fitting before you remove the elevator. Damage can occur.
R (c) Remove and discard the cotter pin (6).
R (d) Remove the bolt (5) and bush (4) from the hinge support.
R NOTE : STA-LOK and CASTELLATED NUT retention systems are____
R interchangeable and both can be installed on the same
R hinge fitting.
R (5) If installation between the elevator and hinge fittings each (No. 1,
R 2, 3, 5 and 6) have STA-LOK nuts, to disconnect them:
R (a) Use TOOL - REMOVAL, WASHERS SL40871 to remove the lockwashers
R (1). Remove the STA-LOK nuts (2). (Ref. TASK 20-22-00-000-001).
R (b) Remove and discard the cotter pins (6).
R (c) Remove the bolts (5) and bushes (4) from all the hinge supports.
R (6) If installation between the elevator and hinge fittings each (No. 1,
R 2, 3, 5 and 6) have castellated nuts, to disconnect them:
R (a) Remove and discard the cotter pins (9).
R (b) Remove the castellated nuts (7).
R (c) Remove and discard the cotter pins (6).
R (d) Remove the bolts (5) and bushes (4) from all the hinge supports.
R (7) Carefully remove the elevator from the hinge arms and lower it onto a
R correct support.
R **ON A/C ALL
Subtask 27-34-41-080-050
B. Removal of Support Equipment
(1) Remove the sling from the elevators.
TASK 27-34-41-400-001
Installation of the Elevator
WARNING : DO NOT GET THE COMPOUND ON YOUR SKIN.
_______
IF YOU DO:
-RUB IT OFF IMMEDIATELY WITH A CLEAN CLOTH
-WASH THE SKIN WITH SOAP AND RINSE WITH CLEAN WATER.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______
MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵3(50)
