• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-21 13:53来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 (2) Put blanking caps on the disconnected electrical connectors. Subtask 27-34-51-020-055
 B. Remove Mode Selector Valve Transducer (MSVT)
 (1)
 Support the MSVT (3) and remove the bolts (4) and the washers (5) holding the MSVT (3) to the servo control actuator.

 (2)
 Remove the MSVT (3) from the servo control actuator.

 (3)
 Remove the O rings (6) and (7).


 1EFF : ALL 1 27-34-51Page 455 1 1 May 01/05R 1 1 1CES 1


 Elevator Servo-Control Actuator Mode Selector Valve Transducer
 Figure 406/TASK 27-34-51-991-005

 1EFF : ALL 1 27-34-51Page 456 1 1 May 01/05R 1 1 1CES 1


 TASK 27-34-51-400-005
 Installation of the Elevator Servo Control Actuator Mode Selector Valve Transducer MSVT WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______
 MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
 DAMAGE.

 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS


 -COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______
 FALL CAN INJURE OR KILL YOU.

 CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
 CARBONFIBER REINFORCED PLASTIC.

 NOTE : The installation of the servo control actuator 34CE1 mode selector valve
____ transducer is given. The installation of the servo control actuator 34CE2, 34CE3 and 34CE4 mode selector transducer valves are the same.
 1.
 Reason for the Job

__________________
 Self Explanatory


 2.
 Job Set-up Information


______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R  No specific Torque Wrench : range 0.00 to 1.20 m.daN
R  (0.00 to 9.00 lbf.ft) 98D27309001000 1 TOOL-ELEVATOR NEUTRAL SETTING 98D27903500000 2 PIN-SIDE STICK LOCKING


 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
 SYNTH.ESTER BASED GREASE HIGH PRESSURE
 (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-34-00-710-001 Operational Test of the Elevator and Hydraulic
 Actuation 29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 55-13-11-000-001 Removal of the THS Trailing Edge Access Panels 55-13-11-400-001 Installation of the THS Trailing Edge Access Panels 27-34-51-991-005 Fig. 406
 3. Job Set-up
__________
 Subtask 27-34-51-860-067
 A. Aircraft Maintenance Configuration
 (1)
 Make sure that the elevators and the horizontal stabilizer are set to the neutral position.

 (2)
 Make sure that the PIN-SIDE STICK LOCKING (98D27903500000) is in the CAPT and F/O side stick controllers.

 (3)
 Make sure that the TOOL-ELEVATOR NEUTRAL SETTING (98D27309001000) is installed on the elevator.

 (4)
 Make sure that the hydraulic systems are depressurized (Ref. TASK 29-10-00-864-001), (Ref. TASK 29-10-00-864-002), (Ref. TASK 29-10-00-864-003).

 (5)
 Make sure that the warning notices are in the flight compartment to tell persons not to operate the flight controls.


 1EFF : ALL 1 27-34-51Page 458 1 1 May 01/05R 1 1 1CES 1


 (6)
 Make sure that the warning notices are in position to tell persons not to operate the hydraulic systems.

 (7)
 Make sure that the access platforms are in position at zone 334 and/or zone 344.

 (8)
 Make sure that access panels 334DB and/or 344DB are open (Ref. TASK 55-13-11-000-001).


 Subtask 27-34-51-865-079
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵3(72)