-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
The manual extension of the flaps.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific pneumatic right-angle wrench No specific safety barriers No specific warning notice No specific access platform 2.5 m (8 ft. 2 in.) 460005835 2 GROUND LOCK SLEEVE 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER 98D27804001000 1 ADAPTOR-DRIVE, SLAT (AND FLAP) 98D27804011000 1 BAR-TURNING
1EFF : ALL 1 27-50-00Page 210 1 1 May 01/04R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External
Power 27-50-00-866-009 Retraction of the Flaps on the Ground 27-54-45-000-002 Removal of the Torque Shaft 6204CM(6254CM) 31-32-00-860-006 Procedure to Get Access to the SYSTEM REPORT/TEST
F/CTL Page 32-12-00-010-001 Open the Main Gear Doors for Access 27-50-00-991-005 Fig. 201
3. Job Set-up
__________
Subtask 27-50-00-941-060
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position on the panel 114VU to tell persons not to operate the flap/slat controls.
Subtask 27-50-00-860-061
B. Aircraft Maintenance Configuration
(1)
Make sure that the flaps are fully retracted (Ref. TASK 27-50-00-866-009).
(2)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER on the flap/slat control lever on panel 114VU.
(3)
Energize the ground service network
(Ref. TASK 24-42-00-861-001).
1EFF : ALL 1 27-50-00Page 211 1 1 May 01/04R 1 1 1CES 1
(4) On the MCDU:
(a) Get access to the SYSTEM REPORT/TEST F/CTL page (Ref. TASK 31-32-00-860-006).
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU: On the MCDU:
-push the line key for <SFCC1(2) - the MCDU shows the SFCC1(2) menu page
1.
2. Push the NEXT PAGE button - the MCDU shows the SFCC1(2) menu page
2.
3.
Push the line key (2R) SYSTEM - the MCDU shows the flap SYSTEM DATA DATA FLP> submenu.
4.
Push the line key (1L) <PPU - the MCDU shows the PPU DATA page(s).
5.
Record the APPU data. Subtask 27-50-00-865-065
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/WTB/FLP/SYS2 12CV P20 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21 122VU FLIGHT CONTROLS/WTB/FLP/SYS1 10CV S07
Subtask 27-50-00-010-052
D. Get Access
(1)
Open the applicable MLG door (Ref. TASK 32-12-00-010-001).
(2)
Install the GROUND LOCK SLEEVE on the applicable main gear door actuator.
(3)
Put the access platform in position below the torque shaft assy 6204CM (6254CM) in the MLG bay.
1EFF : ALL 1 27-50-00Page 212 1 1 May 01/04R 1 1 1CES 1
(4) Remove the torque shaft assy 6204CM (6254CM) (Ref. TASK 27-54-45-000-
002).
4. Procedure
_________ (Ref. Fig. 201/TASK 27-50-00-991-005) Subtask 27-50-00-866-057
A. Manual Extension of the Flaps with Pneumatic Wrench WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Install the ADAPTOR-DRIVE, SLAT (AND FLAP) (98D27804001000) on the right angle gearbox 6203CM (6253CM).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵3(192)
