(69.91 and 84.95 lbf.in).
(e) Safety the nut with a new cotter pin (9).
(3) Connect the elevator to the elevator hinge fitting No. 4.
(a) Apply COMMON GREASE (Material No. 04-004) to the sleeve (17) and the bush (4) and install them.
(b) Install the bolt (5) and safety with a new cotter pin (6).
(c) Put in position and install the elevator support strut (16). (Ref. TASK 55-16-48-400-001).
(4) Connect the elevator servo controls (Ref. TASK 27-34-51-400-001).
(5) Connect the elevator position transducer (Ref. TASK 27-92-13-400-001)
(6) Connect the bonding straps (19) with the bolts (21), the washers (20) and the nuts (18).
(7) Apply STRUCTURE PAINTS (Material No. 16-003) to the bonding connection.
R **ON A/C 051-051,
R Subtask 27-34-41-420-051-A
R A. Installation
R R (1) Remove the support connections, lift the elevator clear of the support and move it to the installation position.
R R R NOTE : STA-LOK and CASTELLATED NUT retention systems are____ interchangeable and both can be installed on the same hinge fitting.
R R R (2) If installation between the elevator and hinge fittings each (No. 1, 2, 3, 5 and 6) have STA-LOK nuts, connect them with PIN-ELEVATOR CENTERING (98D27309004000), and:
R R (a) Apply COMMON GREASE (Material No. 04-004) to the bushes (4) and install them.
R R (b) Apply COMMON GREASE (Material No. 04-004) to the bolts (5) and install them.
R (c) Safety the bolts (5) with new cotter pins (6).
R (d) Install the STA-LOK nuts (2). (Ref. TASK 20-22-00-400-001)
R (e) TORQUE the STA-LOK nuts (2) to between 0.225 and 0.275 m.daN
R (19.91 and 24.33 lbf.in)
R (f) Use TOOL - INSTALLATION, WASHERS SL40871 to install the
R lockwashers (1). (Ref. TASK 20-22-00-400-001)
R (3) If installation between the elevator and hinge fittings each (No. 1,
R 2, 3, 5 and 6) have castellated nuts, connect them with PIN-ELEVATOR
R CENTERING (98D27309004000), and:
R (a) Apply COMMON GREASE (Material No. 04-004) to the bushes (4) and
R install them.
R (b) Apply COMMON GREASE (Material No. 04-004) to the bolts (5) and
R install them.
R (c) Safety the bolts (5) with new cotter pins (6).
R (d) Install and torque the nut (7) to between to between 0.79 and
R 0.96 m.daN (69.91 and 84.95 lbf.in)
R (e) Safety the nuts (7) with new cotter pins (9).
R (4) Install the elevator hinge fitting No. 4.
R (a) Apply COMMON GREASE (Material No. 04-004) to the sleeve (17) and
R bush (4), and install them.
R (b) Install the bolt (5) and safety with a new cotter pin (6).
R (c) Put in position and install the elevator support strut (16).
R (Ref. TASK 55-16-48-400-001).
R (5) Connect the elevator servo controls (Ref. TASK 27-34-51-400-001).
R (6) Connect the elevator position transducer (Ref. TASK 27-92-13-400-001)
R (7) Connect the bonding straps (19) with the bolts (21), the washers (20)
R and the nuts (18).
R (8) Apply STRUCTURE PAINTS (Material No. 16-003) to the bonding
R connection.
R **ON A/C ALL
5. Close-up
________
(Ref. Fig. 401/TASK 27-34-41-991-004)
Subtask 27-34-41-080-051
A. Remove Support Equipment
(1) Remove the hoisting equipment.
(a)
Remove the sling from the elevator.
(b)
Remove the hoisting lugs NSA9006-12B.
(c)
Install the hoist point plugs (10). NOTE : When installed the plugs must fit flush to the skin of the
____
Horizontal Stabilizer.
Subtask 27-34-41-210-051
B. Visual Inspection
(1) Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 27-34-41-410-050
C. Close access
(1) Close the THS lower trailing edge access panels 334BB, 344BB, 334DB, 344DB, 334FB, 344FB, 334GB, 344GB, 334HB, 344HB. (Ref. TASK 55-13-11-400-001).
Subtask 27-34-41-942-050
D. Remove Ground Equipment
(1)
Remove the warning notice(s).
(2)
Remove the access platform(s).
Subtask 27-34-41-081-050
E. Remove Locking Pins
(1) Remove the PIN-SIDE STICK LOCKING (98D27903500000) from the CAPT and F/O side stick controllers.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵3(53)
