Subtask 27-34-00-410-063
B. Close Access.
(1) Close the access door 312AR.
R R (2) Close the THS trailing edge access panels (Ref. TASK 55-13-11-400-001):
(a) 334DB for the left elevator.
(b) 344DB for the right elevator.
(3) Install the protective cover on the battery power center 105VU.
(4) Tighten the two screws.
(5) Close the access door 822 (Ref. TASK 52-41-00-410-002).
(6) Remove the access platform(s).
TASK 27-34-00-820-003- 01
Adjustment of the Elevator and Hydraulic Actuation to 0.5 Degrees Nose-Up with the Gauge-Elevator Neutral Setting (98D27309002000)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______
MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adhesive paper tape
No specific pointer
No specific warning notice
No specific warning notices
No specific access platform 1.6 m (5 ft. 3 in.)
No specific access platform 2.8 m (9 ft. 2 in.)
No specific access platform 5.35 m (17 ft. 7 in.)
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) 0U190360 1 PIN - RIGGING 98D27303000001 1 LOAD APPLICATION TOOL - ELEVATOR, AILERON, RUDDER
R 98D27309002000 1 GAUGE-ELEVATOR NEUTRAL SETTING 98D27903500000 2 PIN-SIDE STICK LOCKING
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
No specific Lockwire-corrosion resistant steel dia 0.8 mm (0.03 in.)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
8 reference triangle 11-21-27 02 -010 R 8 reference triangle 11-21-27 02A-010
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
11-00-00-960-001 Replacement of the Reference Triangle 24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 27-34-00-200-001 Check of the Elevator Servo Controls and Hinge Bearings for too much Play and Condition 27-34-00-710-001 Operational Test of the Elevator and Hydraulic
Actuation 27-34-51-000-001 Removal of the Elevator Servo Control 27-34-51-400-001 Installation of the Elevator Servo Control 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
Power Supply 29-10-00-864-003 Depressurize the Blue Hydraulic System 29-23-00-863-001 Pressurize the Green Hydraulic System from the Yellow
Hydraulic System through the PTU with the Electric Pump 29-23-00-864-001 Depressurize the Green and Yellow Hydraulic Systems after Operation of the PTU 29-24-00-863-001 Pressurize the Yellow Hydraulic System with the Electric Pump 29-24-00-864-001 Depressurize the Yellow Hydraulic System
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R 55-13-11-000-001 55-13-11-400-001 27-34-00-991-001 27-34-00-991-009 27-34-00-991-010 27-34-00-991-008 Removal of the THS Trailing Edge Access Panels Installation of the THS Trailing Edge Access PanelsFig. 501Fig. 502Fig. 505Fig. 506
3. Job Set-up__________
Subtask 27-34-00-010-066
A. Get Access.
(1) Put the access platform in position in zone 312.
(2) Put the access platform in position in these zones:
(a) 334 for the left elevator.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵3(34)
