(2)
From this mark, measure the distance along the skin between the edge of the stucture and the center of the triangle.
NOTE : The position of the triangle must be between 386 mm (15.1968
____
in.) and 402 mm (15.8267 in.).
(a) If the position of the triangle is not between these two values:
-do not adjust the elevators with the reference triangle
-adjust the elevators with the GAUGE-ELEVATOR NEUTRAL SETTING (98D27309002000) or GAUGE-ELEVATOR NEUTRAL SETTING (98D27309006000), (Ref. TASK 27-34-00-820-003) or (Ref. TASK 27-34-00-820-003).
(b) If the position of the triangle is between these two values:
-the position of the triangle is correct; no maintenance action is necessary.
(3)
Put the access platform in position under the right elevator.
(4)
Make a mark at 780 mm (30.7086 in.) from the forward corner of the APU access door 316AR.
(5)
From this mark, measure the distance along the skin between the edge of the stucture and the center of the triangle.
NOTE : The position of the triangle must be between 386 mm (15.1968
____
in.) and 402 mm (15.8267 in.).
Triangle Reference on the Tail Cone
Figure 605/TASK 27-34-00-991-012-A
1EFF : ALL 1 27-34-00 Page 633
1 1 May 01/04
1 1
1CES 1
(a) If the position of the triangle is not between these two values:
-do not adjust the elevators with the reference triangle
-adjust the elevators with the GAUGE-ELEVATOR NEUTRAL SETTING (98D27309002000) or GAUGE-ELEVATOR NEUTRAL SETTING (98D27309006000), (Ref. TASK 27-34-00-820-003) or (Ref. TASK 27-34-00-820-003).
(b) If the position of the triangle is between these two values:
-the position of the triangle is correct; no maintenance action is necessary.
5. Close-up
________
Subtask 27-34-00-410-065-A
A. Close Access
(1)
Remove the warning notice(s).
(2)
Remove the access platform(s).
ELEVATOR - REMOVAL/INSTALLATION
_______________________________
TASK 27-34-41-000-001
Removal of the Elevator
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______
MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______
FALL CAN INJURE OR KILL YOU.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
CARBONFIBER REINFORCED PLASTIC.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific crane
No specific warning notices
No specific NSA9006-12B
No specific access platform 3.5 m (11 ft. 6 in.)
R SL90-627-3125 1 TOOL - REMOVAL, WASHERS SL40871 98D27903500000 2 PIN-SIDE STICK LOCKING 98D55209004000 1 SLING-ELEVATOR
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-22-00-000-001 Removal of STA-LOK Nuts and Lockwashers
27-34-51-000-001 Removal of the Elevator Servo Control
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵3(48)
