e Feed the surplus cable (small amount only) back up the
_ flexible conduit to the junction box (bracket assembly) on the rear spar.
f Make sure that the supply cable is held tight by the P-clip
_
at the cable guide.
NOTE : It is important that the fuel pump supply cable is
____ installed correctly as given in steps b_ thru f_. Incorrect installation of the cable can cause it to get damaged. If the cable is too short it will put tension on the wires and plug. If the cable is too long you will not be able to install the fairings correctly. This is because the unwanted cable (excess length) will become looped and get trapped during the installation of the intermediate and rear fairings.
7 In the cockpit (right rear) do a visual inspection as
_ specified in step (j)2_ of the items that follow, replace if necessary:
a The C/B-FUEL/L WING TK/PUMP 1 SPLY (1QA) at the C/B panel
_
121VU (Ref. AWM 93-01-21).
b The connector 2212VC-A and related receptacle at the panel
_
120VU (Ref. AWM 93-01-20).
8 Release the front face of the C/B panel 121VU and lower to the
_
open (horizontal) position.
9 Use a multimeter and make sure that each of the 115VAC three
_ phases are available at the C/B-1QA input and output terminals (Ref. ASM 28-21/01).
10 If the 115VAC supply to the C/B-1QA, is not available at
__ terminals A1, B1 and C1 trouble shoot the AC supply (Ref. TSM 24 PB 101).
11 If, with the C/B-1QA closed, the 115VAC supply is not
__ available at the terminals A2, B2 and C2, replace the C/B-FUEL/L WING TK/PUMP 1 SPLY (1QA).
12 Raise the front face of the C/B panel 121VU to the closed
__ (vertical) position and secure.
13 In the forward avionics bay remove the front cover of the
__ contactor box 107VU (Ref. AWM 93-01-07).
14 Do a visual inspection as specified in step (j)2_ and replace,
__ if necessary:
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-105, 151-154, ∞∞28-21-00∞∞∞∞∞∞∞∞∞∞Page 206
201-207, May 01/05 CES
a_ The CNTOR-L WING TK PUMP 1 SPLY (17QA).
b_ The connector 1264VC-A and related receptacle.
15__ Remove the contactor 17QA.
16__ Use a multimeter and make sure that each of the 115VAC three phases are available at the contactor base input sockets (8, 6 and 2) (Ref. ASM 28-21/01).
17__ If the 115VAC supply to the contactor 17QA is not available, do a test of the aircraft wiring (three phase supply) between the C/B-FUEL/L WING TK/PUMP 1 SPLY (1QA) and the CNTOR-L WING TK PUMP 1 SPLY (17QA) (Ref. ASM 28-21/01). Do the test as follows:
a_ Continuity test, with a multimeter, of each three phase wire (from end to end) (Ref. ESPM 20-52-21).
b_ Insulation test, with a 500VDC insulation tester, between each phase wire (pole) and ground (Ref. ESPM 20-52-24).
c_ Insulation test, with a 500VDC insulation tester, between each phase wire and the other two wires (pole to pole) (Ref. ESPM 20-52-24).
d_ Repair/replace the unserviceable wiring and connectors.
e_ Install the contactor 17QA.
f_ Install the the front cover of the contactor box 107VU.
18__ If the 115VAC supply is available, install the contactor 17QA.
19__ Set the L TK PUMPS 1 P/BSW (13QA) to ON (push in). This will energize the contactor 17QA and the 115VAC three phases will be supplied to the contactor 17QA output terminals, 7, 5 and 1.
20__ Use a multimeter to do a test, to make sure that each of the 115VAC three phases are available at the terminal block 1176VT, terminals 8A, 8F and 9B (Ref. AWM 28-21-01).
21__ Set the L TK PUMPS 1 P/BSW (13QA) to OFF (released out). This will de-energize the contactor 17QA.
22__ If the 115VAC is not available at the terminal block, replace the CNTOR-L WING TK PUMP 1 SPLY (17QA).
a_ Install the front cover of the contactor box 107VU.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-105, 151-154, ∞∞28-21-00∞∞∞∞∞∞∞∞∞∞Page 207
201-207, May 01/05 CES
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 FUEL 燃油1(67)
