TASK 24-38-00-810-836
Intermittent Warning because of an Internal Failure of the BCL1
1. Possible Causes
_______________
- BCL-1 (1PB1)
- ELEC BAT1 pushbutton switch (7PB1)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 24-38-00-710-001 Operational Test of the Battery Charge Limiter (BCL), (without the CFDS) AMM 24-38-34-000-001 Removal of the Battery Charge Limiter (BCL) (1PB1, 1PB2) AMM 24-38-34-400-001 Installation of the Battery Charge Limiter (BCL) (1PB1, 1PB2)
3. Fault Confirmation
__________________
A. Test
Not applicable, the failure is intermittent.
4. Fault Isolation
_______________
A. If the fault symptom is identified by the warning BCL1 FAULT without CFDS message:
- release, and push again the ELEC BAT1 pushbutton switch (7PB1).
(1) If the fault continues:
- replace the BCL-1 (1PB1) (Ref. AMM TASK 24-38-34-000-001) and (Ref. AMM TASK 24-38-34-400-001).
B. Do the Operational Test of the BCL (without CFDS) (Ref. AMM TASK 24-38-00-710-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-38-00∞∞∞∞∞∞∞∞∞∞Page 257
Aug 01/00R
CES TASK 24-38-00-810-837
Intermittent Warning because of an Internal Failure of the BCL2
1. Possible Causes
_______________
- BCL-2 (1PB2)
- ELEC BAT2 pushbutton switch (7PB2)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 24-38-00-710-001 Operational Test of the Battery Charge Limiter (BCL), (without the CFDS) AMM 24-38-34-000-001 Removal of the Battery Charge Limiter (BCL) (1PB1, 1PB2) AMM 24-38-34-400-001 Installation of the Battery Charge Limiter (BCL) (1PB1, 1PB2)
3. Fault Confirmation
__________________
A. Test
Not applicable, the failure is intermittent.
4. Fault Isolation
_______________
A. If the fault symptom is identified by the warning BCL2 FAULT without CFDS message:
- release, and push again the ELEC BAT2 pushbutton switch (7PB2).
(1) If the fault continues:
- replace the BCL-2 (1PB2) (Ref. AMM TASK 24-38-34-000-001) and (Ref. AMM TASK 24-38-34-400-001).
B. Do the Operational Test of the BCL (without CFDS) (Ref. AMM TASK 24-38-00-710-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞24-38-00∞∞∞∞∞∞∞∞∞∞Page 258
Aug 01/00R
CES TASK 24-38-00-810-838
Incorrect Discharge of the Battery 2
1. Possible Causes
_______________
R - SEC-1 (1CE1) R - SEC-2 (1CE2) R - SEC-3 (1CE3)
- PRESS SW-B HYD, FLT CTL (10CE1)
- PRESS SW-G HYD, FLT CTL (10CE2)
- PRESS SW-Y HYD, FLT CTL (10CE3)
- ELAC-2 (2CE2)
- BCL-2 (1PB2)
- BAT-2 (2PB2)
- PRESS SW-FLT CTL, G (1151GN)
- PRESS SW-FLT CTL, B (2151GN)
- PRESS SW-FLT CTL, Y (3151GN)
- RELAY-ELAC2 EMER SPLY (48CE)
- RELAY-ELAC1 BATT SPLY BREAKING (35CE)
- RELAY-SEC1 BATT SPLY BREAKING
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific ammeter
No specific warning notice(s)
B. Referenced Information 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址:A320 Trouble Shooting Manual 排故手册 电源 3(70)